苏州hp报修电话696l6769,> 维修资料 > hp > 苏州HP Color LaserJet 5500售后维修电话696l6769> 苏州hp打印机维修服务网

hp Color LaserJet 5500常见故障代码描述,英文手册

更新时间:2024/3/13 6:20:47,view:127

hpHP Color LaserJet 5500打印机苏州hp一体机服务中心电话0512-696l6769,苏州hpHP Color LaserJet 5500维修站,hpHP Color LaserJet 5500苏州维修站,hpHP Color LaserJet 5500维修手册,hpHP Color LaserJet 5500在线技术交流,有问必答,hpHP Color LaserJet 5500小故障自己查询维修资料即可解决问题

Code: 10.XX.YY
Display:
10.XX.YY SUPPLIES ERROR
Description:
The printer cannot read or write to at least one print cartridge memory tag or at least one memory tag is missing.
XX Description: 00 memory error on supply item 10 memory tag missing
YY Description: 00 black print cartridge 01 cyan print cartridge 02 magenta print cartridge 03 yellow print cartridge
Remedy:
1 Turn the printer off and then back on. 2 Swap the cartridge for the color indicated with a cartridge in another slot to determine whether the error follows the cartridge or stays with the slot. If the error follows the cartridge, replace that cartridge. Otherwise, continue with step 3. 3 Reseat the connectors between the memory PCB (J601-J605) and the antenna PCBs (J903), the memory PCB, and the DC controller PCB (J1122). 4 Replace the antenna PCB. 5 Replace the memory PCB. 6 Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 13.XX.YY
Display:
13.XX.YY.DUPLEX JOB INTERRUPTED
Description:
A duplex job was interrupted by interference as media passed through the output bin during duplexing.
Remedy:
1 Press for ? more information. 2 Remove one or two pages from the output bin as directed by the display. 3 Press GO to continue printing. NOTE: If JAM RECOVERY = OFF some pages will not be reprinted. Re-send the missing pages.
Code: 13.XX.YY
Display:
13.XX.YY.JAM IN DUPLEX PATH
Description:
There is a jam in the duplex path.
Remedy:
1 Press ? for detailed information about clearing the jam. 2 Press up and down to step through the instructions. 3 Check if the ETB rollers or gears are worn or defective. Replace the ETB if they are. 4 Check the duplex feed guide, which is part of the control panel crossmember assembly. If the guide is worn or damaged, replace the crossmember assembly.
Code: 13.XX.YY
Display:
13.XX.YY.JAM IN PAPER INPUT PATH
Description:
There is a jam in the media input path.
Remedy:
1. Press ? for detailed information about clearing the jam. 2. Press up and down to step through the instructions. 3. Check the registration shutter, and make sure it is in place. Replace the paper pickup assembly if the shutter is damaged. 4. Check the paper pickup feed rollers, and replace them if they are worn or damaged. 5. Check the connectors, gears, solenoid, clutch, motors, sensors, and PCBs on the paper pickup assembly. Replace the paper pickup assembly if necessary. 6. Check the cassette lifter mechanism for proper operation.
Code: 13.XX.YY
Display:
13.XX.YY JAM IN PAPER PATH
Description:
There is a jam in the media path.
Remedy:
1. Press ? for detailed information about clearing the jam. 2. Press up and down to step through the instructions. 3. If paper is folding into an accordion shape, check whether the shutter on each print cartridge opens as you close the ETB and if each cartridge is turning properly. Replace defective print cartridges or drive motors. 4. Clean the attaching roller at the bottom of the ETB and make sure the spring is holding it in place. 5. If the attaching roller gears are defective, replace the ETB. Calibrate the printer after replacing the ETB. 6. Replace the paper pickup PCB. 7. Replace the ETB if it is not moving paper properly. Calibrate the printer. 8. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 13.XX.YY
Display:
13.XX.YY JAM IN TRAY 1
Description:
A page is jammed in the multipurpose tray.
Remedy:
1. Press ? for detailed information about clearing the jam. 2. Press up and down to step through the instructions. 3. Clean the pickup roller. If it is worn or damaged, replace it. 4. Clean or replace the separation pad. 5. Replace the Tray 1 pickup solenoid. 6. Replace the pickup motor. 7. Replace the paper pickup assembly. 8. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 13.XX.YY
Display:
13.XX.YY JAM IN TRAY 2
Description:
A page is jammed in Tray 2.
Remedy:
1. Press ? for detailed information about clearing the jam. 2. Press up and down to step through the instructions. 3. Clean the pickup roller. If it is worn or damaged, replace it. 4. Clean the feed roller. If it is worn or damaged, replace it. 5. Replace the Tray 2 pickup clutch. 6. Replace the pickup motor. 7. Replace the paper pickup assembly. 8. Check the cassette lifter mechanism for proper operation. 9. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 13.XX.YY
Display:
13.XX.YY JAM IN TRAY X
Description:
A page is jammed in Tray 3 or Tray 4.
Remedy:
1. Press ? for detailed information about clearing the jam. 2. Press up and down to step through the instructions. 3. Clean the pickup roller. If it is worn or damaged, replace it. 4. Clean the feed roller. If it is worn or damaged, replace it. 5. Replace the Tray 3 or Tray 4 pickup clutch. 6. Replace the Tray 3 or Tray 4 pickup motor. 7. Replace the Tray 3 or Tray 4 paper feeder PCB. 8. Check the cassette lifter mechanism for proper operation. 9. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 20
Display:
20 INSUFFICIENT MEMORY
Description:
The printer has received more data from the computer than fits in available memory.
Remedy:
1. Press GO to resume printing. Note A loss of data will occur. 2. Reduce the complexity of the print job to avoid this error. 3. Adding memory to the printer may allow printing of more complex pages.
Code: 22
Display:
22 EIO X BUFFER OVERFLOW
Description:
The printer’s EIO card in slot X has overflowed its I/O buffer during a busy state.
Remedy:
Press GO to resume printing. Note A loss of data will occur.
Code: 22
Display:
22 PARALLEL I/O BUFFER OVERFLOW
Description:
The printer’s parallel buffer has overflowed during a busy state.
Remedy:
Press GO to resume printing. Note A loss of data will occur.
Code: 22
Display:
22 SERIAL I/O BUFFER OVERFLOW
Description:
The printer’s serial buffer has overflowed during a busy state.
Remedy:
Press GO to resume printing. Note A loss of data will occur.
Code: 40
Display:
40 BAD SERIAL TRANSMISSION
Description:
A serial data error (parity, framing, or line overrun) has occurred while the printer was receiving data.
Remedy:
Press GO to resume printing. Note A loss of data will occur.
Code: 40
Display:
40 EIO X BAD TRANSMISSION
Description:
A connection with the card in EIO slot X has been abnormally broken
Remedy:
1. Press GO to resume printing. Note A loss of data will occur. 2. Check that all cables are connected to the EIO ports and that the EIO board is seated properly. 3. If possible, print to another network printer to verify the network is working properly.
Code: 41.3
Display:
41.3 UNEXPECTED SIZE IN TRAY X
Description:
Media is loaded which is longer or shorter in the feed direction than the size configured for the tray.
Remedy:
1. If the incorrect size was selected, cancel the job or press ? to access help. 2. Press up and down to step through the instructions.
Code: 41.5
Display:
41.5 UNEXPECTED TYPE IN TRAY X
Description:
The printer senses a different media type in the media path than configured in the tray.
Remedy:
1. If the incorrect type was selected, cancel the job or press to access ? help. 2. Press up and down to step through the instructions.
Code: 41.X
Display:
41.X PRINTER ERROR
Description:
A printer error has occurred.
X Description: 1 unknown misprint error 2 beam detect misprint error 3 media feed error (size) 4 no VSYNC error 5 media feed error (type) 6 ETB detection error 7 feed delay error 9 noise VSREQ
Remedy:
1. Press GO to continue or press for more information. 2. If the message persists, turn the printer off and then back on.
Code: 49.XXXX
Display:
49.XXXX PRINTER ERROR
Description:
A critical firmware error has occurred that caused the processor on the formatter to abort operation. This type of error can be caused by invalid print commands, corrupt data, or invalid operations. In some cases, electrical noise in the cable can corrupt data during transmission to the printer. Other causes include poor quality parallel cables, poor connections, or homegrown applications. On rare occasions, the formatter is at fault, which is usually indicated by a 79 Service Error.
Remedy:
1. Press CANCEL JOB to clear the print job from the printer memory. 2. Turn the printer off and then back on. 3. Try printing a job from a different software application. If the job prints, go back to the first application and try printing a different file. If the message appears only with a certain software application or print job, contact the software vendor for assistance. 4. If the message persists with different software applications and print jobs, disconnect all cables to the printer that connect it to the network or PC. 5. Turn the printer off. 6. Remove all memory DIMMs or third-party DIMMs from the printer. (Do not remove the firmware DIMM in slot J1.) 7. Remove all EIO devices from the printer. 8. Turn the printer on. 9. If the error no longer exists, install each DIMM and EIO device one at a time, making sure to turn the printer off and back on as you install each device. 10. Replace a DIMM or EIO device if you determine that it causes the error. 11. Remember to reconnect all cables that connect the printer to the network or computer. 12. If the error persists, replace the firmware DIMM. 13. Replace the formatter and calibrate the printer.
Code: 50.X
Display:
50.X FUSER ERROR
Description:
A fuser error has occurred.
X Description: 1 low fuser temperature 2 fuser warmup service 3 high fuser temperature 4 faulty fuser 5 inconsistent fuser 6 open fuser 8 low fuser temperature (sub=thermistor) 9 high fuser temperature (sub=thermistor)
Remedy:
1. Turn the printer off and allow it to cool down. 2. Reinstall the fuser, and check the connector (J100) that connects the fuser and the printer. Replace the connector if it is damaged. 3. Turn the printer off and remove the fuser. Measure the resistance between the connector pins on the fuser. If resistance does not meet the following guidelines, replace the fuser. J100LB-5 to J100LB-6: 300 - 500 KOhms J100LB-1 to J100LB-2: less than 1 KOhm 4. Check for continuity between connector pins J100-5 and J100-6. If there is no continuity, replace the fuser. 5. Replace the fuser power supply PCB. 6. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 51.XY
Display:
51.XY PRINTER ERROR
Description:
A printer error has occurred.
X Description: 1 beam detect error 2 laser error Y Description 0 no color K black C cyan M magenta Y yellow
Remedy:
1. Press GO to continue. 2. Turn the printer off and then back on. 3. Reseat the connectors between the laser/scanner (J74 - J77) and DC controller PCB (J1106 - J1109). 4. Replace the defective laser/ scanner assembly. Calibrate the printer after replacing the laser/scanner. 5. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller
Code: 52.XY
Display:
52.XY PRINTER ERROR
Description:
A printer error has occurred.
X Description: 1 scanner error 2 scanner startup error 3 scanner rotation error Y Description 0 no color K black C cyan M magenta Y yellow
Remedy:
1. Press GO to continue. 2. Turn the printer off and then back on. 3. Reseat the connectors between the laser/scanner (J74 - J77) and DC controller PCB (J1106 - J1109). 4. Replace the defective laser/ scanner assembly. Calibrate the printer after replacing the laser/scanner. 5. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller
Code: 53.10.05
Display:
53.10.05 PRINTER ERROR
Description:
A DIMM is installed in both 168- pin DIMM Slot 4 and 100-pin DIMM Slot 5.
Remedy:
This is an invalid configuration. DIMMs can not be installed in both of these slots at the same time. Remove one of the DIMMs, or move one of the DIMMs to a different slot.
Code: 53.X0.ZZ
Display:
53.X0.ZZ PRINTER ERROR
Description:
A DIMM is installed in both 168- pin DIMM Slot 4 and 100-pin DIMM Slot 5.
Remedy:
This is an invalid configuration. DIMMs can not be installed in both of these slots at the same time. Remove one of the DIMMs, or move one of the DIMMs to a different slot.
Code: 53.X0.ZZ
Display:
53.X0.ZZ PRINTER ERROR
Description:
An error has occurred in the onboard RAM.
Remedy:
1. Press GO to continue. 2. Turn the printer off and then back on.
Code: 53.XY.ZZ
Display:
53.XY.ZZ PRINTER ERROR
Description:
An error occurred on some memory of the printer.
X DIMM Type: 1 RAM
Y Device Location: 1 DIMM Slot 1 2 DIMM Slot 2 3 DIMM Slot 3 4 DIMM Slot 4
ZZ Error Number: 0 unsupported memory 1 unrecognized memory 2 unsupported memory size 3 failed RAM test 4 exceeded maximum RAM size 5 invalid DIMM speed
Remedy:
Press CANCEL JOB. If the problem persists, replace the DIMM card in the slot indicated.
Code: 54.XX
Display:
54.XX PRINTER ERROR
Description:
X Description: 1 temperature 3 image density sensor 5 color plane registration sensor 6 image density sensor 7 yellow drum home position sensor 8 magenta drum home pos. sensor 9 cyan drum home position sensor 10 black drum home position sensor 11 yellow density sensor 12 magenta density sensor 13 cyan density sensor 14 black density sensor 19 ETB speed control sensor 20 color plane registration sensor 21 yellow toner level sensors 22 magenta toner level sensors 23 cyan toner level sensors 24 black toner level sensors 1E or 30 Half tone calibration error
Remedy:
Turn the printer off and then back on, then check items in the order listed. 54.1 error Check the fuser. See 50.X fuser error. 54.30 error Wipe sensor lens clean. Run a full calibration and the error should go away. 54.3 error Check the connections. Replace the color registration detection assembly. 54.5 error Check the connections. Replace the color registration detection assembly. 54.6 error Check the connections. Replace the color registration detection assembly. 54.7, 54.8, 54.9, or 54.10 error Check the connections. Replace the drum phase sensor for the indicated color. 54.11, 54.12, 54.13, or 54.14 error Check the connections. Check the cartridge and replace it if necessary. Replace the color registration detection assembly. 54.19 error Check the ETB connection. Replace the ETB. Replace the DC controller. 54.20 error Check the connection. Replace the color registration detection assembly. 54.21, 54.22, 54.23, or 54.24 error Check the connections. Replace the toner level sensing PCB. Replace the DC controller.
Code: 55.X
Display:
55.X PRINTER ERROR
Description:
The DC controller is not communicating with the formatter. The problem could be caused by a timing error or an intermittent connection.
Remedy:
1. Press to continue. 2. Turn the printer off and then back on. 3. Reseat or replace the connectors between the DC controller and the formatter. 4. If the problem persists, replace the DC controller PCB. Calibrate the printer after replacing the DC controller. 5. Replace the formatter. Initialize NVRAM.
Code: 57.X
Display:
57.X PRINTER ERROR
Description:
A printer fan error has occurred.
X Description: 3 cartridge fan (vertical fan, FM3) 4 formatter fan (horizontal fan, FM2) 7 power suppply fan (FM1)
Remedy:
Turn the printer off and then back on.
57.3 Cartridge fan error (FM3)
1. Reconnect the connectors J10 for the cartridge fan and J1102 on the DC controller PCB. 2. Immediately after starting the print operation, measure the voltage between pins 1 and 3 on the J10 connector. If the voltage changes from 0 V to 12 V or 24 V, replace the cartridge fan. 3. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
57.4 Formatter fan error (FM2)
1. Reconnect the connectors J11 for the formatter fan and J1102 on the DC controller PCB. 2. Immediately after turning the printer on, measure the voltage between pins 4 and 6 on the J1102 connector. If the voltage changes from 0 V to 12 V or 24 V, replace the formatter fan. 3. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
57.7 Power supply fan error (FM2)
1. Reconnect the connectors J1104 and J1133 on the DC controller PCB. 2. Disconnect the connector J1133. Immediately after turning the printer on, measure the voltage between pins 1 and 3 on the J1133 connector. If the voltage changes from 0 V to 12 V or 24 V, replace the power supply fan. 3. Replace the low-voltage power supply. 4. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 58.X
Display:
58.X PRINTER ERROR
Description:
A memory tag error was detected.
X Description: 3 CPU 4 power supply
Remedy:
1. Turn the printer off and then back on. 2. Replace the memory PCB. 3. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Code: 59.XY
Display:
59.XY PRINTER ERROR
Description:
A printer motor error has occurred.
X Description: 0 motor error 1 motor startup error 2 motor rotation error 3 fuser motor startup error 4 fuser motor rotation error 5 print cartridge motor startup error 6 print cartridge motor rotation error 9 ETB motor startup error A ETB motor rotation error B developing disengaging motor startup error C developing disengaging motor rotation error.
Y Description: 0 no color K black C cyan M magenta Y yellow
Remedy:
1. Turn the printer off and then back on. 2. This message might also appear if the transfer unit is missing or incorrectly installed. Ensure that the transfer unit is correctly installed.
ETB motor error
1. Clean the ETB unit intermediate connector, J36. If the connector is damaged, replace it. 2. Reconnect the connetors J38 for the ETB motor and J1111 on the DC controller PCB. 3. Replace the ETB motor. 4. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Fuser motor error
1. Reconnect the connectors J18 for the fuser motor and J1101 on the DC controller PCB. Replace any damaged parts. 2. Replace the fuser drive assembly. 3. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Print cartridge motor error
1. Reconnect the print cartridge connector on the DC controller PCB (J1124 for cyan, J1126 for magenta, J1125 for yellow, and J1127 for black). 2. Replace the drum drive assembly for the indicated print cartridge. 3. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller.
Developing disengaging motor error
1. Reconnect the connectors J16 for the developing disengaging motor and J1100 for the DC controller PCB. 2. Replace the developing disengaging drive assembly. 3. Replace the DC controller PCB. Calibrate the printer after replacing the DC controller
Code: 62
Display:
62 NO SYSTEM
Description:
No system was found.
Remedy:
1. Turn the printer off and then back on. 2. Reseat the firmware DIMM, making sure it is in the 168- pin slot J1.
Code: 64
Display:
64 PRINTER ERROR
Description:
Scan buffer error.
Remedy:
1. Turn the printer off and then back on. 2. Perform a cold reset. 3. If the message persists, replace the formatter or firmware DIMM.

Code: 68.X
Display:
68.X PERMANENT STORAGE ERROR
Description:
One or more printer settings saved in the non-volatile storage device is invalid and has been reset to its factory default. Pressing the button should clear the message. Printing can continue, but there may be unexpected behavior.
X Description: 0 onboard NVRAM 1 removable disk (flash or hard)
Remedy:
1. Press GO to continue. 2. Turn the printer off and then back on. 3. Check the printer settings to determine which settings have been changed.
Code: 68.X
Display:
68.X PERMANENT STORAGE FULL
Description:
A non-volatile storage device is full. Pressing the GO button should clear the message. Printing can continue, but there may be unexpected behavior.
X Description: 0 onboard NVRAM 1 removable disk (flash or hard)
Remedy:
1. Press GO to continue. 2. For 68.0 errors, turn the printer off and then back on. 3. If a 68.0 error persists, execute an NVRAM inititialization. 4. For 68.1 errors, use the hp Web Jetadmin software to delete files from the disk drive. 5. If a 68.1 errors persists, reinitialize the hard disk.
Code: 68.X
Display:
68.X PERMANENT STORAGE WRITE FAIL
Description:
A non-volatile storage device is failing to write. Pressing GO the button should clear the message. Printing can continue, but there may be unexpected behavior.
X Description: 0 onboard NVRAM 1 removable disk (flash or hard)
Remedy:
1. Press GO to continue. 2. Turn the printer off and then back on. 3. If the problem persists, initialize NVRAM. 4. Reinitialize the hard disk.
Code: 79.XXXX
Display:
79.XXXX PRINTER ERROR
Description:
A critical hardware error has occurred.
Remedy:
1. Turn the printer off and then back on. 2. If the problem persists, reseat the firmware DIMM. 3. Reseat the formatter. 4. Replace the firmware DIMM. 5. Replace the formatter. Calibrate the priner.
Code: 8X.YYYY
Display:
8X.YYYY EIO ERROR
Description:
The EIO accessory card in slot X has encountered a critical error.
Remedy:
1. Turn the printer off and then back on. 2. If the problem persists, reseat the EIO card. 3. Replace the EIO card.

热门图文

相关资料补充


热门关注
· hp color laserjet 5550常见故障代码描述,英文手册

· hp color laserjet 8500常见故障代码描述,英文手册1

· hp color laserjet 8500常见故障代码描述,英文手册2

· hp color laserjet 8550常见故障代码描述,英文手册2

· hp color laserjet 8550常见故障代码描述,英文手册1

· hp color laserjet 4730mfp常见故障代码描述,英文手册2

· hp color laserjet 4730mfp常见故障代码描述,英文手册1

· hp color laserjet 9500常见故障代码描述,英文手册2

· hp color laserjet 9500常见故障代码描述,英文手册1

· hp color laserjet cm2320常见故障代码描述,英文手册

· hp color laserjet cm1415常见故障代码描述,英文手册

· hp color laserjet cm1410常见故障代码描述,英文手册

· hp color laserjet cm1017常见故障代码描述,英文手册

· hp color laserjet cm1015常见故障代码描述,英文手册

· hp color laserjet cm1312常见故障代码描述,英文手册

· hp color laserjet cm4540常见故障代码描述,英文手册4

· hp color laserjet cm4540常见故障代码描述,英文手册3

· hp color laserjet cm4540常见故障代码描述,英文手册2

· hp color laserjet cm4540常见故障代码描述,英文手册1

· hp color laserjet cm3530常见故障代码描述,英文手册1

· hp color laserjet cm3530常见故障代码描述,英文手册2

· hp color laserjet cm4730常见故障代码描述,英文手册2

· hp color laserjet cm4730常见故障代码描述,英文手册1

· hp color laserjet cm6030常见故障代码描述,英文手册5

· hp color laserjet cm6030常见故障代码描述,英文手册4

· hp color laserjet cm6030常见故障代码描述,英文手册3

· hp color laserjet cm6030常见故障代码描述,英文手册2

· hp color laserjet cm6030常见故障代码描述,英文手册1

· hp color laserjet cm6040常见故障代码描述,英文手册5

· hp color laserjet cm6040常见故障代码描述,英文手册4

推荐文章
· hp2520hc电源灯闪并亮喊叹号

· hpm128fn加完粉后一直报黑色碳粉不足

· hpm202dw更换硒鼓出现不兼容的墨粉盒

· hpcp1025无法识别芯片

· hp128老提示更换硒鼓

· hp175a开机显示正在初始化后就显示通道卡纸

· hp1606dn提醒指示灯、就绪指示灯和“确定”指示灯亮起

· hpmfp175报49错误

· hplaserjetp1106就绪灯和错误灯同时亮

· hpn126打印机总是自动初始化

· hpm128fn双灯闪烁无显示

· hpm1136打印机激光器扫描架清理

· hpm1136mfp显示hp,然后下面两个灯一直在双闪,无法打印,什么情况

· hp5025错误代码59.20

· hp定影器错误关闭后然后打开

· hpm2727一直初始化

· hpcp5225恢复出厂设置

· hp177fw一体机新机提示安装成像鼓

· 佳能mf4452报警:e2020002接触式传感器hp错误,回路故障

· hp2055扫描打印复印一体机,显示printingdocument然后无反映故障

· hp1005纸刚出定影组件就卡住

· hp2055d开机提示52扫描仪错误

· hp128提示文档进纸器拾取错误

· hpm128fp故障灯一直闪控制面板无显示

· hp126nw提示正在使用用过的碳粉盒

· hpt790绘图仪错误代码79:03

· 79errorhp2600

· hp176开机时为什么电源灯旁的感叹号闪烁

· hpm1213nf打印一张通路卡纸

· hp1055cmip地址查询

· hp-mfpm176n加了粉还提示墨粉量低

· hp3630墨盒加墨水图解

· hp3035错误信息49.ff04

· hplaserjet1100serues显示感叹号

· hpm176一直提示三角感叹号错误是怎么回事

· hp1112开机灯闪烁

· hp系统错误7904关闭电源如果问题仍存在,请致电hp支持中心

· hpp2055d提示49err3d910c8怎么解决

· hpm1005复印薄的文稿有黑影

· hp226dw提示扫描仪错误17关闭然后打开

· hp1280电源灯不亮的真正原因

· hpp1606n不进纸,是什么问题

· hp2025彩色打印机报错59是哪里的问题

· ricohprintersc680

· hpm128fp开机一直显示正在初始化

· hp1319f屏幕 无显

· hp m1005一体机安装程序错误,rpc服务器不可用

· hp m1005 开机报scanner error 20错误,故障原因

· hp1020/hp1020plus/hp1010/hp1007定影器故障夹纸原因

· hp1008打印文稿纸中间有白道,字体模糊?