苏州维修电话696l6769,> 维修资料 > hp > 苏州hpHP DesignJet 2500CP售后维修电话696l6769> 苏州hp打印机维修服务网

hp DesignJet 2500CP常见故障代码描述,英文手册

更新时间:2024/3/28 2:26:20,view:67

HP DesignJet 2500CP打印机苏州漕湖复印机维修服务中心电话0512-696l6769,苏州HP DesignJet 2500CP漕湖维修站,HP DesignJet 2500CP漕湖维修站, hp1020plus 打印一张纸后就卡住, HP打印机显示阿拉伯文, 惠普6800打印机显示重新启动打印机。如果问题仍然存在,请致电hp支持中心, hp 1005w报错50, HP M439nda成像装置不足怎么清除,

苏州hp打印机售后维修服务中心电话0512-696l6769

Code: 0000D8
Description:
Library Error.
Code: 010020
Description:
The Checksum read on the Flash SIMM is incorrect.
Code: 010021
Description:
The baseDRAM or theRAM SIMM tests failed.
Code: 010022
Description:
The SWATH RAM test failed.
Code: 010023
Description:
A fuse on the Main PCA has blown.
Code: 010024
Description:
Problem initializingthe encoder pulse generator.
Code: 010030
Description:
One of the two interconnect boards not detected.
Code: 010031
Description:
The Printhead Primitive Driver ASIC Test Failed.
Code: 010032
Description:
Fan Test Failed -Current not detected in one or bothfans. Error data (XX):
1 -Electronics Module fan not running. 2 -Service station fan not running. 3 -Bothfans not running. 10 -Electronics Module fan is short-circuited. 20 -Service Station fan is short-circuited. 30 -Bothfans are short-circuited. 12 -Service Station fan is not running and the Electronics Module fan is short-circuited. 21 -Electronics Module fan is not running and the Service Station fan is short-circuited.
Code: 010033
Description:
The DC Motor Driver ASIC Test Failed.
Code: 010034
Description:
One of the DC Motors has failed. Error data: 00010000 -Y-axis Motor Failed. 00020000 -X-axis Motor Failed. 00030000 -Both DC Motors Failed.
Code: 010035
Description:
One of the Stepper Motors has failed. Error data (oXABCDEF): If the value of each letter is o, then the component is OK. If the value of each letter is different from 0 then the component has failed. X -Electronics signal failed (ignore other values). A -Elevator Stepper Motor Failed. B -Refill Stepper Motor Failed. C -Primer Stepper Motor Failed. D -Service station (Z-axis) Stepper Motor Failed. E -Service station (X-axis) Stepper Motor Failed. F -Bail Stepper Motor Failed.
Code: 010036
Description:
ADC Test Failure in the Main PCA A short circuit in the Y/X-axis or ANY stepper motor. This short circuit is causing some of the fuses in the Electronics Module to burn. Error data: 00000800 -Problem with the Y-axis. 00001000 -Problem with the X-axis.
Code: 010037
Description:
ADC Test Failure in the Carriage PCA.
Code: 010038
Description:
A Printhead voltage could not be set -Main PCA Failure.
Code: 010039
Description:
A Printhead voltage could not be set -Carriage PCA Failure
Code: 010040
Description:
The Ambient Temperature measured is out of the normal range.
Code: 010042
Description:
The status of one of the opticalsensors is not stable when it should be. Error data (X): 0 -Problem with the Media Sensor. 1 -Problem with the Pinch-arm Sensor. 2 -Problem with the Refill Assembly Sensor. 3 -Problem with the Elevator Sensor. 4 -Problem with the Service Station Sensor. 5 -Problem with the Primer Sensor.
Code: 010043
Description:
Problem with theCarriageBoard.
Code: 010100
Description:
Error reading the EEROM.
Code: 010101
Description:
An action outside the EEROM limits has been performed.
Code: 010102
Description:
Physical EEROM write and/or write operations failed. The EEROM data that is written does not match the data that is read.
Code: 010110
Description:
The content of the permanent configuration area of theEEROM is not valid when theprinter is initialized in Service Mode.
Code: 010111
Description:
The content of the User configuration area of the EEROM is not valid when the printer is initialized.

Code: 010120
Description:
The content of the permanent configuration area of the EEROM is not valid when the printer is initialized in Normal Mode.
Code: 010121
Description:
One of the banks of the user area was corrupted while writing or reading in that area.
Code: 020000
Description:
Error in finding the Primer home position.
Code: 020001
Description:
Error in finding the Elevator home position.
Code: 020002
Description:
Error in finding the Refill Arm home position.
Code: 020003
Description:
Error in finding the Refill Stepper Motor home position.
Code: 020004
Description:
Error in finding the Service Station home position.
Code: 020005
Description:
Elevator has problem reaching a desired position.
Code: 020006
Description:
The refill position in the Y-axis is not calibrated.
Code: 020010
Description:
Problem with fine movement of the Y-axis motor.
Code: 020011
Description:
Error during initialization of the Y-axis.
Code: 040601
Description:
The MIO card does not support the MIO 6 protocol. Cards with version 5 or below can not be used with this plotter. Version 5.1 cards behave as expected but do not support PML instructions. Install the latest version.
Code: 040xxx
Description:
MIO Card Error
Code: 050000
Description:
The Line Sensor has problems finding the Mark Encoder.
Code: 060000
Description:
The Line Sensor is not functioning properly because there is too much ambient light.
Code: 060100
Description:
Incorrect Line Sensor type in the EEROM.

Code: 060200
Description:
Incompatible Firmware and Carriage PCA.
Code: 060300
Description:
Incompatible Firmware and Line Sensor.
Code: 060400
Description:
Incompatible Carriage PCA and Line Sensor OR Line Sensor not calibrated after replacing Carriage Assembly.
Code: 060500
Description:
Line Sensor not calibrated.
Code: 07xxxx
Description:
Firmware Error.
Code: 080001
Description:
Hard Disk Drive installed without PostScript.
Code: 08xxxx
Description:
PostScript Error.
Code: 090004
Description:
PostScript installed without the Hard Disk Drive.
Code: 09xxxx
Description:
Hard Disk Drive Error.

热门图文

相关资料补充


热门关注
· hp designjet 2800cp常见故障代码描述,英文手册

· hp designjet 3000cp常见故障代码描述,英文手册

· hp designjet 3500cp常见故障代码描述,英文手册

· hp designjet 3800cp常见故障代码描述,英文手册

· hp designjet 4000常见故障代码描述,英文手册2

· hp designjet 4000常见故障代码描述,英文手册1

· hp designjet 4020常见故障代码描述,英文手册2

· hp designjet 4020常见故障代码描述,英文手册1

· hp designjet 500常见故障代码描述,英文手册

· hp designjet 5000常见故障代码描述,英文手册

· hp designjet 5500常见故障代码描述,英文手册

· hp designjet 650c常见故障代码描述,英文手册

· hp designjet 700常见故障代码描述,英文手册

· hp designjet 750c常见故障代码描述,英文手册

· hp designjet 755cm常见故障代码描述,英文手册

· hp designjet 8000s常见故障代码描述,英文手册

· hp designjet 510常见故障代码描述,英文手册

· hp designjet 800常见故障代码描述,英文手册

· hp designjet 815常见故障代码描述,英文手册

· hp designjet 9000s常见故障代码描述,英文手册

· hp designjet l25500常见故障代码描述,英文手册1

· hp designjet l25500常见故障代码描述,英文手册2

· hp designjet l26500常见故障代码描述,英文手册2

· hp designjet l26500常见故障代码描述,英文手册1

· hp designjet l28500常见故障代码描述,英文手册4

· hp designjet l28500常见故障代码描述,英文手册3

· hp designjet l28500常见故障代码描述,英文手册2

· hp designjet l28500常见故障代码描述,英文手册1

· hp designjet l65500常见故障代码描述,英文手册3

· hp designjet l65500常见故障代码描述,英文手册4

推荐文章
· hpcp1025打印机显示红色感叹号怎么消除?

· hp5225打印机出现59f0错误

· hpc5180清除卡纸每次开机显示卡纸

· hp9050打印机报错是59:10请问是什

· hpcp1525打印两张后出现cleqningmisprintpress(ok)

· hpm175a出现提示传感器错误怎么办

· hp5200lx显示downldfilenowsendrfuupgrade

· hpofficejet7110打印机进纸闪烁是怎么回事呀,请指教

· hp7000墨盒k灯闪烁是什么原因

· hp2055d打印机为什么一直会闪黄灯

· hp1025打印机显示成像鼓碳粉量不足是什么意思

· hp3015显示51.10错误怎么办

· hpm1005打印机显示printingdocument但是不打印是什么原因

· hp1336打印机感叹号亮黄灯显示e0

· hp5200高压板终于拆出来了

· hp1136激光一体机显示e1是什么意思

· hp500换喷头后出现出现系统错误22:10

· hp7110墨水系统故障0xc19a0020

· hp1010打印机为什么电源指示灯一闪一闪不打印

· hplaserjet5200lx面板上三个灯都亮不工作是怎么回事

· hp2025打2页以上(含2页)就提示jamintray2,当你按ok后出1张白纸后打第2页

· hp1005打印机的进纸通道的传感器的位置在哪

· hp7110只能识别三个墨盒第四个一装上全部都识别不了

· hp2055d打印机开机感叹号亮黄灯屏幕提示removeallpaperfrombinoutputbinisfull

· hplaserjetcp1025color打印机四个灯都在闪,提示黄色碳粉盒内存错误?

· hp1005打印机显示屏显示noprintcartridse时是怎么回事

· hp1213原稿上面下一半,提示文档进纸器拾取错误,重新装入纸张。搞了半天,没好

· hp5200n打印机提示55.04直流控制器错误

· hp50042提示系统错误22:10

· hp系统错误7904关闭电源如果问题仍存在,请致电hp支持中心。

· hp4525dn显示错误59:f0是什么问题?

· hpcp1525n打印红色重影校准也不好使

· hp1566打印机第一打印很快以后变慢

· hp1106显示感叹号灯亮

· hp400打印机提示50.2定影器错误,请关闭打开?

· hp435nw101000耗材记忆错误按ok继续

· hpm226dn打印机,记忆错误清零

· hp5500开机自检80%时提示systemereror0f0100030c09a4switchoff/onifproblempersistscontacthpsupport

· hp1005开机显示hewlell-packarderror:b0603

· hp7110打印机黄色感叹号跳,无法正常打印

· hplaserjetcp1025nwcolor为什么指示灯一直在闪,打印提示脱机

· hp打印机p1106打印时显示热凝器错误怎么办

· hp226dn一体机如何清零

· hp5200 报49.1b03代码 主板

· hpm1005开机无反应,如何判别是电源板还是主板的问题实拍图示说明.jpg

· hp2025颜色平面定位传感器错误

· hplaserjet9050dn错误代码49.2f83error

· hp2520hc电源灯闪并亮喊叹号

· hpm128fn加完粉后一直报黑色碳粉不足

· hpm202dw更换硒鼓出现不兼容的墨粉盒