苏州hp打印机售后维修服务中心电话0512-696l6769

Code: 44:11
Description:
Aerosol Fan not connected.
Remedy:
• Check that the Aerosol Fan cable is not damaged and is correctly connected to the Interconnect PCA. • Replace the Aerosol Fan.
Code: 51.1:10
Description:
PHC Access Door Sensor failure.
Remedy:
• Check that the PHC Access Door Sensor cable is not damaged and is correctly connected to the Interconnect PCA. • Replace the PHC Access Door Sensor.
Code: 51:10
Description:
Window Sensor failure.
Remedy:
• Check that the Window Sensor cable is not damaged and is correctly connected to the Interconnect PCA. • Replace the Window Sensor.
Code: 52:10
Description:
Drop Detector switch On/Off failure.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Drop Detector cable is not damaged and is correctly connected to the Service Station cable. • Check that the Service Station cable is not damaged and is correctly connected to the Interconnect PCA. • Replace the Drop Detector. • Replace the Gamut PCI PCA. • If the System Error continues, replace the Interconnect PCA. Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
Code: 53:10
Description:
Media Sensor failure.
Remedy:
• Check that the Media Sensor cable is not damaged and is connected correctly to the Interconnect PCA. • Replace the Media Sensor.
Code: 54:10
Description:
Media Lever Sensor failure.
Remedy:
• Check that the Media Lever Sensor cable is not damaged and is connected correctly to the Interconnect PCA. • Replace the Media Lever Sensor.
Code: 55:10
Description:
Problem with the Line Sensor.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Replace the Line Sensor. • If the System Error continues, replace the Carriage PCA.
Code: 56:03
Description:
Analog Encoder calibration failed.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Replace the Encoder Disc and Sensor. • If the System Error continues, replace the PrintMech PCA.
Code: 56:10
Description:
Analog Encoder calibration failed.
Remedy:
• Replace the Encoder Disc and Sensor.
Code: 61:01
Description:
The file format is incorrect and the Printer cannot process the job.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check the graphic language setting of the Printer (Refer to the User’s Guide). • Resend the file to the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 61:04.1
Description:
The Postscript fonts are missing. Upgrading the Firmware will re-install the fonts.
Remedy:
Perform a full firmware upgrade that includes package ’B’.
Code: 61:08.1
Description:
The file cannot be printed because it is password protected.
Remedy:
Resend the file without password protection.
Code: 63:04
Description:
Input/Output problem through the Network Card.
Remedy:
• Check that the Network cable is correctly connected to the Network Card. • If a Gigabit Ethernet Card is being used, make sure it is correctly installed. If necessary, replace the Gigabit Ethernet Card. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version. • If the System Error continues, replace the Main PCA.
Code: 64:04
Description:
Input/Output problem through the USB Port.
Remedy:
• Check that the USB cable is correctly connected to the Printer. • Check that the USB Card is correctly installed. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version. • Replace the USB card.
Code: 65:04
Description:
Input/Output problem through an unknown port.
Remedy:
• Check that the unknown port cable is correctly connected to the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 66:08
Description:
Cannot print file on current paper type. The paper type has changed since the file was sent, so the file cannot be printed on the paper type currently loaded.
Remedy:
• Resend the file to be printed on the current paper type. • Change the paper type to the type that was loaded when the file was originally sent.
Code: 67:04
Description:
Input/Output problem through an Firewire Port.
Remedy:
• Check that the Firewire cable is correctly connected to the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version. • If the System Error continues, replace the Main PCA.
Code: 68:03
Description:
Non-critical permanent data was lost. This does not prevent the Printer to work, only that internal life counters will not be recorded until the Printer is restarted.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 71:03
Description:
Out of memory failure.
Remedy:
It is recommended that you remove any unnecessary files from the Hard Disk Drive using the Web Server.
Code: 71:04
Description:
Out of memory failure.
Remedy:
It is recommended that you remove any unnecessary files from the Hard Disk Drive using the Web Server.
Code: 71:19
Description:
Default Serial Number found in the main and backup NVM. It seems that both the Ink Supply Tubes and Hard Disk Drive have been replaced together.
Remedy:
• Perform the "Error 71:19 Recovery" Service Utility (refer to Chapter 4). You MUST NEVER replace both the Hard Disk Drive and the Ink Supply Tubes and Trailing Cable at the same time. If both parts need to replaced, you MUST first replace one part and then power ON the Printer until it completely initializes. Then you can power OFF the Printer and replace the other part.

Code: 72:04
Description:
Generic Firmware error.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 73:03
Description:
Servo Error.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version. • Perform the "Scan-Axis" Diagnostic to further troubleshoot the error code. • If the System Error continues, perform the "Media Drive" Diagnostic to further troubleshoot the error code.
Code: 74:00
Description:
Failed getting Part Number/Serial Number.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 74:01
Description:
Error uploading firmware update file.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Resend the firmware update file to the Printer.
Code: 74:04
Description:
Old Vacuum Fan detected - upgrade the Firmware.
Remedy:
• Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 76:03
Description:
Out of Disk space - Data was lost.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Resend the file to the Printer. • If the System Error continues, it is recommended that you remove any unnecessary files from the Hard Disk Drive using the Web Server. • Perform an EEROM Reset and resend the file to the Printer.
Code: 77:04
Description:
Embedded Web Server internal software error.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 79.1:04
Description:
CDS server lost connection with client.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.

Code: 79:03
Description:
Generic Firmware error.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 79:04
Description:
Generic Firmware error.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Printer has the latest Firmware version. If not, update the Firmware to the latest version.
Code: 81:01
Description:
Paper servo shutdown.
Remedy:
• Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Perform the "Media Drive" Diagnostic to further troubleshoot the error code. • If the System Error continues, replace the Media-Axis Motor.
Code: 81:03
Description:
It was impossible to correctly stop the servo before setting the encoder position.
Remedy:
• Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Perform the "Media Drive" Diagnostic to further troubleshoot the error code. • If the System Error continues, replace the Media-Axis Motor.
Code: 81:10
Description:
Fail starting Paper Motor.
Remedy:
• Open the Window and check for any visible obstacles restricting the movement of the Drive Roller. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Perform the "Media Drive" Diagnostic to further troubleshoot the error code. • If the System Error continues, replace the Media-Axis Motor.
Code: 85:03
Description:
Problem finding the Drive Roller zero.
Remedy:
• Perform the "Media Drive" Diagnostic to further troubleshoot the error code.
Code: 86:01
Description:
Carriage servo shutdown.
Remedy:
• Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Check that the Carriage Stopper is correctly installed (Refer to Carriage Disassembly Instructions, Step 16.). • Perform the "Scan-Axis" Diagnostic to further troubleshoot the error code. • If the System Error continues, replace the Scan-Axis Motor.
Code: 86:03
Description:
Scan-Axis length test failure.
Remedy:
• Perform the "Scan-Axis" Diagnostic to further troubleshoot the error code.
Code: 86:10
Description:
Initializing Scan-Axis Motor failure.
Remedy:
• Switch the Power OFF from the back of the Printer and disconnect the Power cord. Reconnect the power cord and power On the Printer. • Check that the Carriage Belt is correctly installed. • Replace the Encoder Strip and Encoder Sensor. • If the System Error continues, replace the Scan-Axis Motor.
Code: 86:11
Description:
Scan-Axis length too short.
Remedy:
• Open the Window and check for any visible obstacles restricting the movement of the Carriage Assembly. If there is a wrinkled mass of media inside the paper path, lift the Pinchwheels (using the Media Lever) and clear the obstruction. • Replace the Encoder Strip and Encoder Sensor.
Code: 91:02
Description:
The hp Instant Support troubleshooting tool has detected that at least one Printhead has been replaced without having a specific error, and without being recovered/cleaned.
Remedy:
Advise the customer that the next time they want to replace a Printheads they should make sure that at least a Printhead Recovery is performed.
Code: 91:10
Description:
The hp Instant Support troubleshooting tool has detected that at least, for one Printhead: It is currently in warranty (less than 1000cc of ink used). That the previous 2 Printheads had been found defective within the warranty period.
Remedy:
In this case, it is possible that the Printer is damaging the Printhead. If, after replacing the Printhead a third time, it is found to be defective again, you may need to troubleshoot the Carriage Flex Cables or the Carriage PCA.
Code: 93:11
Description:
Unable to pressurize the IDS.
Remedy:
• Remove ALL the Ink Cartridges and reinstall them one by one in to the Printer. • Replace the Ink Cartridges. • Replace the APS Assembly. • If the System Error continues, replace the Ink Supply Tubes and Trailing Cable.
Code: 98:02
Description:
Switching to lower performance due to Printhead quality.
Remedy:
• Try a Printhead recovery on the Printheads. • Replace the faulty Printhead. You may have to print the Image Quality Diagnostics print in order to identify the faulty Printhead.

热门图文

相关资料补充