苏州hp报修电话696l6769,> 维修资料 > hp > 苏州HP LaserJet Enterprise MFP M630售后维修电话696l6769> 苏州hp打印机维修服务网

hp LaserJet Enterprise MFP M630常见故障代码描述,英文手册1

苏州hp报修电话696l6769,维修点查询,售后服务,上门维修,技术服务,客户服务,维修手册,用户手册

更新时间:2024/4/11 0:51:07,view:95

HP LaserJet Enterprise MFP M630打印机苏州元和一体机维修服务中心电话0512-696l6769,苏州HP LaserJet Enterprise MFP M630元和维修站,HP LaserJet Enterprise MFP M630元和维修站, hp 451 出纸一半 提示卡纸, hp1108打印提示热凝器错误, hp1510打印机冷启动, hp1005打印打印完多进纸半张卡住, hp 451 对位辊,

Code: 10.00.00
Display:
10.00.00, 10.00.10 Supply memory error
Description:
The product cannot read or write to at least one print cartridge memory tag or a memory tag is missing from the print cartridge. Memory error (Y = 0) • 10.00.00 (event code) Black print cartridge Memory tag missing (Y = 1) • 10.00.10 (event code) Black print cartridge
Remedy:
1. Remove, and then reinstall the indicated print cartridge. 2. If the error reappears, turn the power off, and then on. 3. Check the cartridge memory tag. If it is damaged, replace the cartridge. 4. If the error persists, replace the indicated print cartridge.
Code: 10.00.10
Display:
10.00.00, 10.00.10 Supply memory error
Description:
The product cannot read or write to at least one print cartridge memory tag or a memory tag is missing from the print cartridge. Memory error (Y = 0) • 10.00.00 (event code) Black print cartridge Memory tag missing (Y = 1) • 10.00.10 (event code) Black print cartridge
Remedy:
1. Remove, and then reinstall the indicated print cartridge. 2. If the error reappears, turn the power off, and then on. 3. Check the cartridge memory tag. If it is damaged, replace the cartridge. 4. If the error persists, replace the indicated print cartridge.
Code: 10.23.5X
Display:
10.23.5X Fuser Kit Reset
Description:
• 10.23.50 (event code) The fuser kit life was reset above the order threshold. • 10.23.51 (event code) The fuser kit life was reset above the replace threshold. • 10.23.52 (event code) The fuser kit life was reset above the reset threshold.
Remedy:
No action necessary.
Code: 10.23.70
Display:
10.23.70 Printing Past Very Low
Description:
The product indicates when fuser kit is very low. The actual remaining fuse kit life might vary. You do not need to replace the fuser yet unless print quality is unacceptable.
Remedy:
If print quality is no longer acceptable, replace the fuser kit. See the parts chapter in the service manual for the fuser kit part number.
Code: 10.XX.33
Display:
10.XX.33 Used Supply In Use
Description:
The print cartridge is used. • 10.00.33 (event code) Black print cartridge.
Remedy:
Using a cartridge that is near its end-of-life can cause this event code.
Code: 10.XX.34
Display:
10.XX.34 Used Supply In Use
Description:
The print cartridge is used. • 10.00.34 (event code) Black print cartridge
Remedy:
NOTE: Removing a cartridge from one product and then installing it in a different product (for testing functionality) will cause this event code.
Code: 10.XX.40
Display:
10.XX.40 Genuine hp Supplies Installed
Description:
A genuine hp print cartridge has been installed. • 10.00.40 (event code) Black print cartridge
Remedy:
No action necessary.
Code: 10.XX.41
Display:
10.XX.41 Unsupported Supply In Use
Description:
The installed print cartridge is for a different product. • 10.00.41 (event code) Black print cartridge
Remedy:
Remove the print cartridge, and then install the correct cartridge for this product.
Code: 10.XX.70
Display:
10.XX.70 Printing past very low
Description:
The product indicates when a supply level is very low. The actual remaining print cartridge life might vary. You do not need to replace the print cartridge at this time unless print quality is no longer acceptable. • 10.00.70 (event code) Black print cartridge
Remedy:
If print quality is no longer acceptable, replace the print cartridge. See the parts chapter in the service manual for the correct cartridge part number.
Code: 10.YY.15
Display:
10.YY.15 Install
Description:
The indicated supply has been removed or installed incorrectly. • 10.00.70 (event code) Black print cartridge • 10.23.15 (event code) Fuser kit
Remedy:
Replace or install the indicated supply. See the parts chapter in the service manual for the correct supply or kit part number.
Code: 10.YY.35
Display:
10.YY.35 Incompatible
Description:
The indicated supply is not compatible with this product. • 10.00.35 (event code) Black print cartridge • 10.23.35 (event code) Fuser kit
Remedy:
Install a supply that is designed for this product. See the parts chapter in the service manual for the correct supply part number.
Code: 11.00.01
Display:
11.00.01 or 11.00.02 Internal clock error
Description:
The product real time clock has experienced an error. 01=dead clock 02=dead real time clock
Remedy:
1. Whenever the product is turned off and then turned on again, set the time and date on the control panel. 2. If the error persists, you might need to replace the formatter.
Code: 11.00.02
Display:
11.00.01 or 11.00.02 Internal clock error
Description:
The product real time clock has experienced an error. 01=dead clock 02=dead real time clock
Remedy:
1. Whenever the product is turned off and then turned on again, set the time and date on the control panel. 2. If the error persists, you might need to replace the formatter.
Code: 13.80.Ax
Display:
13.80.Ax Jam inside left cover
Description:
Paper jam in stapler/stacker input feed sensor SR5 • 13.80.A1 Stopped going to Bin 1 • 13.80.A2 Stopped going to Bin 2 number.|
Remedy:
1. Follow the on screen instructions to locate and remove the paper or obstruction. 2. Inspect the paper path and remove any obstructions. 3. Remove and reattach output accessory. 4. Verify that the input sensor (SR5) responds correctly. 5. Replace Output Accessory.
Code: 13.84.A4
Display:
13.84.A4 Jam inside left cover
Description:
A jam exists in the lower bin area.
Remedy:
1. Follow the on screen instructions to locate and remove the paper or obstruction. 2. Inspect the paper path and remove any obstructions. 3. Remove and reattach output accessory. 4. Verify that the input sensor (SR5) responds correctly. 5. Replace Output Accessory.
Code: 13.85.Ax
Display:
13.85.Ax Jam inside left cover
Description:
A jam exists in the accessory output bin area. • 13.80.A1 Output Bin 1 • 13.80.A2 Output Bin 2 • 13.80.A3 Output Bin 3 • 13.80.A4 Lower Output Bin
Remedy:
1. Follow the on screen instructions to locate and remove the paper or obstruction. 2. Inspect the paper path and remove any obstructions. 3. Remove and reattach output accessory. 4. Verify that the input sensor (SR5) responds correctly. 5. Replace Output Accessory.

Code: 13.A1.D1
Display:
13.A1.D1 Jam in Tray 1
Description:
Paper Delay Jam in Tray 1. This jam occurs when the paper does not reach the TOP sensor (Registration sensor) (PS-103) in designated amount of time after the start of paper pick-up from Tray 1. This is a no-pick jam from tray 1 (MP Tray).
Remedy:
1. Clear the jam in the area indicated. 2. Make sure that the MP tray paper guides are set to the correct paper size in the tray, and that the paper is not overload above the marking shown on the tray side guide 3. Check the Tray 1 pickup and feed rollers for wear, damage or paper dusk. Clean or replace the rollers as needed. 4. Perform a test print job, do the rollers turn and feed paper when the product tries to print from Tray 1? • IF YES: Test the feed sensor using the sensor test under the- Administration - Troubleshooting - Diagnostic Tests menu to verify that the sensor is functioning properly. • IF NO: Run the Tray 1 pickup/feed motor drive test under the . Administration - Troubleshooting - Diagnostic Tests- menu to verify that the feed motor is functioning properly. If the test fails or if there is an abnormal noise replace the MP (Tray 1) pickup assembly.
Code: 13.A1.FF
Display:
13.A1.FF Paper Jam
Description:
Residual paper Jam in tray 1 This jam occurs when residual paper is detected at the (Registration sensor) (PS103) at power on.
Remedy:
1. Clear the jam in the area indicated. 2. Close the door to allow the product to attempt to clear the jam. 3. Make sure sensor PS103 flag moves smoothly and that sensor is not damaged. If the flag is damaged replace the MP tray assembly. 4. Test the feed sensor using the sensor test under the - Administration - Troubleshooting - Diagnostic Tests menu to verify that the sensor is functioning properly. 5. If tray 1 does not function properly, replace the MP (Tray 1) pickup assembly.
Code: 13.A2.A2
Display:
13.A2.A2 Jam in tray 2
Description:
Paper Stay Jam tray 2 This jam occurs when the Prefeed sensor (PS102) does not detect the trailing edge of the paper within a specified period of time from when the sensor detected the leading edge.
Remedy:
1. Open tray, remove any jammed paper, and then close the tray. 2. Open and close the right door and clear any paper found to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on the tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or that is out of specification for the tray and product. 5. Verify that the Tray 2 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 2 pickup/feed motor drive test. If the motor is not functioning properly, replace the pickup assembly. 7. Use the manual sensor tests to toggle the Prefeed sensor PS102. If the sensor is not functioning properly. 8. Check the connectors at the sensor and feed motor, and the DC controller PCA. 9. If the error persists, replace the paper pickup assembly.
Code: 13.A2.D2
Display:
13.A2.D2 Jam in tray 2
Description:
Paper Delay Jam from tray 2 This jam occurs when the paper does not reach the Prefeed sensor (PS102) in designated amount of time after the start of paper pick-up from Tray 2. This is a no-pick jam from tray 2.
Remedy:
1. Open tray, remove any jammed paper, and then close the tray. 2. Open and close the right door and clear any paper found to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on the tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or that is out of specification for the tray and product. 5. Verify that the Tray 2 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 2 pickup/feed motor drive test. If the motor is not functioning properly, replace the pickup assembly. 7. Use the manual sensor tests to toggle the Prefeed sensor PS102. If the sensor is not functioning properly. 8. Check the connectors at the sensor and feed motor, and the DC controller PCA. 9. If the error persists, replace the paper pickup assembly.
Code: 13.A2.FF
Display:
13.A2.FF
Description:
Residual Media Jam in Tray 2 This jam occurs when residual media is detected at the prefeed sensor (PS102).
Remedy:
1. Open Tray 2, remove any jammed paper, and then close the tray. 2. Open and close the upper right door to allow the product to attempt to clear the jam. 3. Make sure that the Tray 2 pickup, feed, and separation roller are installed correctly and show no damage or wear. 4. Clean or replace the pickup/feed rollers as needed. 5. Check the connectors at the sensor, feed motor, and the DC controller PCA. 6. Open the following menus: • Administration • Troubleshooting • Diagnostic Tests 7. Test PS102 using the Tray/Bin Manual sensor test to verify that the sensors are functioning correctly. 8. Run the Tray 2 pickup/feed motor drive test to verify that the feed motor is functioning correctly (listen for the motor to activate). If it is not, replace the pickup assembly. 9. If the error persists, replace the paper pickup assembly.
Code: 13.A3.A3
Display:
13.A3.A3 Jam in tray 3
Description:
Paper Stay Jam In Tray 3. This jam occurs when the Tray feed sensor (SR4) does not detect the trailing edge of the paper within a specified period of time from when the sensor detected the leading edge.
Remedy:
1. Open tray, remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or out of specification for the product. 5. Verify that the Tray 3 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 3 pickup/feed motor drive test. If the motor is not functioning properly, replace the Pick up Motor. 7. Use the manual sensor tests to toggle SR4. If the sensor is not functioning properly, replace the Tray 3 Pick up Assembly. 8. Check the following connectors for Tray 3 on the HCI controller and assembly. (J13, J408 Media feed sensor) (J18, J408 Pick up assembly (J14, J409 Pick up motor) 9. If the error persists, replace the Tray 3 paper pickup assembly.
Code: 13.A3.D3
Display:
13.A3.D3 Jam in tray 3
Description:
Paper Delay Jam In Tray 3. This jam occurs when the paper does not reach the Tray 3 feed sensor (SR4) in designated amount of time after the start of paper pick-up from Tray 3. This is a no-pick jam from tray 3.
Remedy:
1. Open tray, remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or out of specification for the product. 5. Verify that the Tray 3 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 3 pickup/feed motor drive test. If the motor is not functioning properly, replace the Pick up Motor. 7. Use the manual sensor tests to toggle SR4. If the sensor is not functioning properly, replace the Tray 3 Pick up Assembly. 8. Check the following connectors for Tray 3 on the HCI controller and assembly. (J13, J408 Media feed sensor) (J18, J408 Pick up assembly (J14, J409 Pick up motor) 9. If the error persists, replace the Tray 3 paper pickup assembly.
Code: 13.A3.FF
Display:
13.A3.FF Paper Jam
Description:
Residual paper jam in Tray 3. This jam occurs when residual paper is detected at the Tray 3 feed sensor (SR4) at power on.
Remedy:
1. Open the tray, and right door and remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 4. Verify that the Tray 3 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 5. Use the manual sensor tests to toggle SR4. If the sensor is not functioning properly, replace the Tray 3 Pick up Assembly. 6. Check the following connectors for Tray 3 on the HCI controller and assembly. (J13, J408 Media feed sensor) (J18, J408 Pick up assembly (J14, J409 Pick up motor) 7. If the error persists, replace the Tray 3 paper pickup assembly.

Code: 13.A4.A4
Display:
13.A4.A4 Jam in tray 4
Description:
Paper Stay Jam In Tray 4. This jam occurs when the paper does not reach the Tray 4 feed sensor (SR8) in designated amount of time after the start of paper pick up from Tray 4.
Remedy:
1. Open the tray, remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper being installed into the tray, and that the tray is not over filled above fill mark on tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or out of specification. 5. Verify that the Tray 4 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 4 pickup/feed motor drive test. If the motor is not functioning properly, replace the Pick up Motor. 7. Use the manual sensor tests to toggle SR8. If the sensor is not functioning properly, replace the Tray 4 pick up assembly. 8. Check the following connectors for Tray 4 on the HCI controller and assembly. (J22, J406 Media feed sensor) (J20 J406 Pick up assembly) (J14, J409 Pick up motor) 9. If the error persists, replace the Tray 4 paper pickup assembly.
Code: 13.A4.D4
Display:
13.A4.D4 Jam in tray 4
Description:
Paper Delay Jam In Tray 4. This jam occurs when the paper does not reach the Tray 4 feed sensor (SR8) in designated amount of time after the start of paper pick-up from Tray 4. This is a no-pick jam from tray 4.
Remedy:
1. Open the tray, remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper being installed into the tray, and that the tray is not over filled above fill mark on tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or out of specification. 5. Verify that the Tray 4 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 4 pickup/feed motor drive test. If the motor is not functioning properly, replace the Pick up Motor. 7. Use the manual sensor tests to toggle SR8. If the sensor is not functioning properly, replace the Tray 4 pick up assembly. 8. Check the following connectors for Tray 4 on the HCI controller and assembly. (J22, J406 Media feed sensor) (J20 J406 Pick up assembly) (J14, J409 Pick up motor) 9. If the error persists, replace the Tray 4 paper pickup assembly.
Code: 13.A4.FF
Display:
13.A4.FF Paper Jam
Description:
Residual paper jam in Tray 4. This jam occurs when residual paper is detected at the Tray 4 feed sensor (SR8) at power on.
Remedy:
1. Open Tray, and right door and remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 4. Verify that the Tray 4 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 5. Use the component tests to run the Tray 4 pickup/feed motor drive test. If the motor is not functioning properly, replace the Pick up motor. 6. Use the manual sensor tests to toggle SR8. If the sensor is not functioning properly, replace the Tray 4 pick up assembly. 7. Check the connectors for Tray 4 on the HCI controller and assembly. (J22, J406 Media feed sensor) (J20 J406 Pick up assembly) 8. If the error persists, replace the Tray 4 paper pickup assembly.
Code: 13.A5.A5
Display:
13.A5.A5 Jam in tray 5
Description:
Paper Stay Jam In Tray 5. This jam occurs when the paper does not reach the Tray 5 feed sensor (SR12) in designated amount of time after the start of paper pick up from Tray 5.
Remedy:
1. Open the tray, remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or out of specification 5. Verify that the Tray 5 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 5 pickup/feed motor drive test. If the motor is not functioning properly, replace the Pick up Motor. 7. Use the manual sensor tests to toggle SR12. If the sensor is not functioning properly, replace the Tray 5 pick up assembly. 8. Check the connectors for Tray 5 on the HCI controller and assembly. (J32, J403 Media feed sensor) (J30, J403 Pick up assembly) (J14, J409 Pick up motor) 9. If the error persists, replace the Tray 5 paper pickup assembly.
Code: 13.A5.D5
Display:
13.A5.D5 Jam in tray 5
Description:
Paper Delay Jam In Tray 5. This jam occurs when the paper does not reach the Tray 5 feed sensor (SR12) in designated amount of time after the start of paper pick-up from Tray 5. This is a no-pick jam from tray 5.
Remedy:
1. Open the tray, remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 4. Avoid loading paper that is damaged (ex. bent, torn, dusty, wrinkled, and curled) and or out of specification 5. Verify that the Tray 5 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 6. Use the component tests to run the Tray 5 pickup/feed motor drive test. If the motor is not functioning properly, replace the Pick up Motor. 7. Use the manual sensor tests to toggle SR12. If the sensor is not functioning properly, replace the Tray 5 pick up assembly. 8. Check the connectors for Tray 5 on the HCI controller and assembly. (J32, J403 Media feed sensor) (J30, J403 Pick up assembly) (J14, J409 Pick up motor) 9. If the error persists, replace the Tray 5 paper pickup assembly.
Code: 13.A5.FF
Display:
13.A5.FF Paper Jam
Description:
Residual paper jam in Tray 5. This jam occurs when residual paper is detected at the Tray 5 feed sensor (SR12) at power on.
Remedy:
1. Open the tray, and right door and remove any jammed paper, and then close the tray. 2. Open and close any door on the product to allow the product to attempt to clear the jam. 3. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 4. Verify that the Tray 5 pickup, feed, and separation rollers are correctly installed and that they are not worn or damaged. Clean or replace the rollers as needed. 5. Use the manual sensor tests to toggle SR12. If the sensor is not functioning properly, replace the Tray 5 pick up assembly. 6. Check the connectors for Tray 5 on the HCI controller and assembly (J32, J403 Media feed sensor) (J30, J403 Pick up assembly) 7. If the error persists, replace the Tray 5 paper pickup assembly.
Code: 13.AA.EE
Display:
13.AA.EE Paper Jam
Description:
HCI Door Open Jam. This jam occurs when the HCI right door (SW1) is opened during printing.
Remedy:
1. Close the lower right door to allow the product to attempt to clear the jam. 2. Test SW1 using the manual sensor switch test under the – Administration- Troubleshooting- Diagnostic Tests- menu to verify that the switch is functioning properly. 3. Replace the SW1 sensor assembly.
Code: 13.Ax.EE
Display:
13.Ax.EE
Description:
This jam occurs when a door is opened during printing. • 13.AB.EE (event code) HCI door open • 13.BB.EE (event code) Right door open
Remedy:
Make sure that the doors are fully closed. Test sensor using the manual sensor switch test under the – Administration- Troubleshooting- Diagnostic Tests- menu to verify that the switch is functioning properly.
Code: 13.B2.Az
Display:
13.B2.Az Paper Jam
Description:
Paper stopped at the registration jam, from the tray indicated. This jam occurs when the paper is present longer than "the expected paper length plus 50mm or more?h when detected at the registration sensor PS103. • 13.B2.A1 = Tray 1 • 13.B2.A2 = Tray 2 • 13.B2.A3 = Tray 3 • 13.B2.A4 = Tray 4 • 13.B2.A5 = Tray 5 • 13.B2.AD = Duplexert
Remedy:
1. Open the top cover and clear the jam in the indicated area. Inspect the paper path and make sure that no paper is blocking the paper path. 2. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 3. Test TOP sensor/Registration Sensor (PS103) using the manual sensor test under the following: Administration Troubleshooting Diagnostic Test Manual Sensor Test elevate the case following your standard support process. 4. If the sensor is functioning properly, run a few pages to check where the leading edge of the paper actually stops. 5. Check the area where the leading edge of the paper has stopped for blockage or damage. Remove any obstructions that are found.
Code: 13.B2.Bz
Display:
13.B2.Bz Jam in top cover
Description:
Multifeed jam at registration sensor (Top Sensor) PS103 • 13.B2.B1 This jam occurs when a multifeed is detected at the Registration sensor PS103 when printing from the Tray 1. • 13.B2.B2 This jam occurs when a multifeed is detected at the Registration sensor PS103 when printing from the Tray 2. • 13.B2.B3 This jam occurs when the media is present longer than "the expected media length plus 50mm" or more is detected at the Registration sensor PS103 when printing from the Tray 3. • 13.B2.B4 This jam occurs when a multifeed is detected at the Registration sensor PS103 when printing from the Tray 4. • 13.B2.B5 This jam occurs when a multifeed is detected at the Registration sensor PS103 when printing from the Tray 5. • 13.B2.AD This jam occurs when a multifeed is detected at the Registration sensor PS103 when printing from the Duplexer.dm
Remedy:
Multifeeds are a media or tray pickup issue. Perform the following steps 1. Open top cover and clear the jam in the indicated area. Inspect the paper path and ensure no paper blocking the paper path. 2. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray 3. Make sure the type and quality of the media that you are using meet hp specifications. 4. Make sure that the Tray pickup, feed, and separation roller are installed correctly and show no damage or wear. 5. Clean or replace the pickup/feed rollers as needed. 6. Check the paper tray for damage and replace tray as needed.
Code: 13.B2.DD
Display:
13.B2.DD Jam in duplexer
Description:
Paper Delay Jam at Registration Top This is a paper delay jam at registration sensor PS103 from the duplexer re-feed.
Remedy:
1. Open top cover and right door and inspect the paper path and ensure no paper blocking the paper path. 2. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 3. Verify that the media meets hp media specifications. 4. Remove the duplexer and remove any media or obstructions found. 5. If issue remains, replace the duplexer
Code: 13.B2.Dz
Display:
13.B2.Dz Jam in top cover
Description:
Paper Delay Jam at Registration Top Paper Delay jam at Registration area?fs TOP sensor (PS103) (Late arriving at sensor) 13.B2.Dz (?gz?h being the tray which the paper was fed from: Tray 1-6) An error code appears on the control panel as 13.B2.D(1-6). Paper Jam. • 13.B2.D1 This jam occurs when the paper is picked from Tray 1 and SP103 is not triggered. • 13.B2.D2 This jam occurs when the paper is picked from Tray 2 and PS102 is triggered, but PS103 is not triggered. • 13.B2.D3: This jam occurs when the paper is picked from Tray 3 and SR4 is triggered, but PS103 is not triggered. • 13.B2.D4: This jam occurs when the paper is picked from Tray 5 and SR8 is triggered, but PS103 is not triggered. • 13.B2.D5: This jam occurs when the paper is picked from Tray 5 and SR12 is triggered, but PS103 is not triggered. Call Out 1 - PS103 Top Sensor Call Out 2 - PS102 Prefeed Sensor NOTE: PS102 and PS103 are not replaceable or removable.
Remedy:
If paper was fed from Tray 1 (MP) (13.B2.D1): Probable cause is a tray 1 misfeed (mispick). Replace Tray 1 feed rollers and make sure paper is properly identified in control panel. If paper was fed from Trays 2-5 or the duplexer: The error indicates that the paper did activate PS102 (Prefeed Sensor) but did not reach PS103 (TOP Sensor). Before beginning repair: IF printer is found still signaling error: • Before opening the printer, do a control panel test to see what sensors are activated and write them down. (Especially note the states of PS101, PS102, PS103, PS107, and PS907). • Note locations or any paper found in paper path and especially those found just before or after PS103 in the registration area. Run a set of internal pages: • Are all of the 13.B2.Dx errors from the same paper tray • How often are they occurring Try to recreate the error: • Using the Event log, determine which tray(s) the error is occurring from then run single sided copies from that tray to try to recreate the error. • Replace the feed, Pickup and separation rollers for paper trays with errors. • Adjust the paper tray guides and load the paper according to procedure stated at the end of this document. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. • Try to recreate the error again, using that same tray. • If error still occurs, then continue to the troubleshooting section of this document before removing the jammed paper from the printer. 1. 1. Open the top cover and MP door and remove the toner cartridge to expose the paper path at the registration area. Inspect the paper path, take note as to where any paper and the paper’s leading edge is located and if simplex or duplex job was being run. Also inspect the leading edge of the paper for any signs of the paper catching on something. 2. If the leading edge of the paper closest to the registration assembly is past PS103 then the problem is most likely with the sensing of the paper with PS103 3. Use Manual sensor test to verify consistent operation of the Registration TOP sensor. Administration Troubleshooting Diagnostic Test Manual Sensor Test Scroll down until PS103 TOP is displayed When activating PS103 sensor, watch the control panel display for the sensor state to change from green to clear or clear to green. I might take a few seconds to change as you toggle sensor flag.
Code: 13.B2.FF
Display:
13.B2.FF Paper Jam
Description:
Residual paper jam in the registration area. This jam occurs when residual paper is detected at the registration sensor (PS103) at power on.
Remedy:
1.Open the top cover and clear the jam in the indicated area. Inspect the paper path and make sure no paper is blocking the paper path. 2. Make sure that the tray width and length guides are set to the correct paper size being installed into the tray and that the tray is not over filled above fill mark on tray. 3. Test printer from other trays to verify functionality and if issue is specific to a one specific tray. 4. Try flossing the printer through the jam access door. • Place paper in access door. • Turn off then back on printer. • Watch for Page to be pulled into printer and fed through paper path. 5. Verify if print job was being duplexed. 6. Check if the pre-registration roller is dirty, worn or deformed. Clean the pre-registration roller if dirty. Replace the roller if it is worn or deformed. 7. Check the registration assembly. Verify the spring of the registration is in correct position. Replace the registration assembly if the registration shutter is scarred or worn. 8. Check and reconnect the connector (J94) on the DC controller PCA.

热门图文

相关资料补充


热门关注
· hp laserjet ii常见故障代码描述,英文手册

· hp laserjet iid常见故障代码描述,英文手册

· hp laserjet iii常见故障代码描述,英文手册

· hp laserjet iiid常见故障代码描述,英文手册

· hp laserjet iiip常见故障代码描述,英文手册

· hp laserjet iip常见故障代码描述,英文手册

· hp laserjet m1005 mfp常见故障代码描述,英文手册

· hp laserjet m1120 mfp常见故障代码描述,英文手册

· hp laserjet m1130 pro常见故障代码描述,英文手册

· hp laserjet m1132 pro常见故障代码描述,英文手册

· hp laserjet m1136 pro常见故障代码描述,英文手册

· hp laserjet m1210 pro常见故障代码描述,英文手册

· hp laserjet m1212 pro常见故障代码描述,英文手册

· hp laserjet m1213 pro常见故障代码描述,英文手册

· hp laserjet m1214 pro常见故障代码描述,英文手册

· hp laserjet m1216 pro常见故障代码描述,英文手册

· hp laserjet m1217 pro常见故障代码描述,英文手册

· hp laserjet m125 pro常见故障代码描述,英文手册

· hp laserjet m1530 pro常见故障代码描述,英文手册

· hp laserjet m1536 pro常见故障代码描述,英文手册

· hp laserjet m126 pro常见故障代码描述,英文手册

· hp laserjet m127 pro常见故障代码描述,英文手册

· hp laserjet m128 pro常见故障代码描述,英文手册

· hp laserjet m1319 mfp常见故障代码描述,英文手册

· hp laserjet m1522 mfp常见故障代码描述,英文手册

· hp laserjet m176 color pro常见故障代码描述,英文手册

· hp laserjet m177 color pro常见故障代码描述,英文手册

· hp laserjet m201n pro常见故障代码描述,英文手册

· hp laserjet m202dw pro常见故障代码描述,英文手册

· hp laserjet m225dw pro常见故障代码描述,英文手册

推荐文章
· 佳能mf4452报警:e2020002接触式传感器hp错误,回路故障

· hp2055扫描打印复印一体机,显示printingdocument然后无反映故障

· hp1005纸刚出定影组件就卡住

· hp2055d开机提示52扫描仪错误

· hp128提示文档进纸器拾取错误

· hpm128fp故障灯一直闪控制面板无显示

· hp126nw提示正在使用用过的碳粉盒

· hpt790绘图仪错误代码79:03

· 79errorhp2600

· hp176开机时为什么电源灯旁的感叹号闪烁

· hpm1213nf打印一张通路卡纸

· hp1055cmip地址查询

· hp-mfpm176n加了粉还提示墨粉量低

· hp3630墨盒加墨水图解

· hp3035错误信息49.ff04

· hplaserjet1100serues显示感叹号

· hpm176一直提示三角感叹号错误是怎么回事

· hp1112开机灯闪烁

· hp系统错误7904关闭电源如果问题仍存在,请致电hp支持中心

· hpp2055d提示49err3d910c8怎么解决

· hpm1005复印薄的文稿有黑影

· hp226dw提示扫描仪错误17关闭然后打开

· hp1280电源灯不亮的真正原因

· hpp1606n不进纸,是什么问题

· hp2025彩色打印机报错59是哪里的问题

· ricohprintersc680

· hpm128fp开机一直显示正在初始化

· hp1319f屏幕 无显

· hp m1005一体机安装程序错误,rpc服务器不可用

· hp m1005 开机报scanner error 20错误,故障原因

· hp1020/hp1020plus/hp1010/hp1007定影器故障夹纸原因

· hp1008打印文稿纸中间有白道,字体模糊?

· hp1005经常夹纸,并且纸夹在定影器处

· hp1213收发不了传真问题

· hp1025彩色打印机加粉步骤

· hp5200打印白纸,无字问题原因

· hp1025机器偏色校准

· hp5200lx提示13.20.00顶盖卡纸,解决方案

· hp1536解除密码方法

· hp1536打印机打印靠右侧坚向全白,换硒鼓打印故障以旧

· hp designjet 500 ,800系列打印机 - 打印结束后不裁纸并报错 6105

· hp t610/t1100显示要更换裁刀的处理方法

· hp500绘图仪是打印时每隔10cm就出现一次重影

· hp designjet 500与800打印内容左右有重影

· hp designjet 500 和 800 系列打印机 - 系统错误 6105 processing job

· hp designjet 100和110系列绘图仪报错误代码0113 错误代码

· hp designjet系列绘图仪打印线条失真如何解决

· hp designjet系列绘图仪喷嘴堵塞如何解决

· hp designjet t610绘图仪报系统错误 7104

· hp500/800系列绘图仪常见故障2110