苏州hp打印机维修服务网 > 维修资料 > hp > 苏州hpHP LaserJet M602售后维修电话696l6769 > 正文

hp LaserJet M602常见故障代码描述,英文手册2

更新时间:2024/3/29 1:01:05,view:139

HP LaserJet M602打印机苏州相城复印机维修站电话0512-696l6769,苏州HP LaserJet M602相城维修站,HP LaserJet M602相城维修站, HP Deskjet 2132按复印件指示灯闪烁, hp1020plus 打印一张纸后就卡住, Hpcp1518ni不上纸, HP1025同时闪粉盒黑蓝红, 惠普126a一直显示HP重启又正常,

Code: 32.1C.09
Display:
32.1C.09
Description:
Tried to restore a backup file that was not valid for this product
Remedy:
Use a valid backup file

Code: 32.1C.0A
Display:
32.1C.0A
Description:
Backup file is invalid
Remedy:
Use a valid backup file Reboot and observe state of product Do a partition clean using the Preboot menu
Code: 32.1C.0B
Display:
32.1C.0B
Description:
Backup is from newer version of FW than what is currently on the product
Remedy:
Use a valid backup file or put correct firmware version on the product.
Code: 32.1C.0C
Display:
32.1C.0C
Description:
Backup cancelled from the hp Embedded Web Server
Remedy:
No action necessary
Code: 32.1C.0D
Display:
32.1C.0D
Description:
Backup/restore failed, auto-reboot failed, or the product might be busy
Remedy:
Reboot and then retry the backup/restore
Code: 32.1C.0E
Display:
32.1C.0E
Description:
Backup/restore timeout while communicating with the formatter
Remedy:
Turn the product off then on and retry
Code: 32.1C.0F
Display:
32.1C.0F
Description:
Backup/restore timeout while communicating with the finisher firmware
Remedy:
Turn the product off then on and retry
Code: 32.1C.10
Display:
32.1C.10
Description:
Backup/restore timeout while communicating with the scanner firmware
Remedy:
Turn the product off then on and retry
Code: 32.1C.11
Display:
32.1C.11
Description:
Backup/restore timeout while communicating with the engine
Remedy:
Turn the product off then on and retry

Code: 32.1C.12
Display:
32.1C.12
Description:
Backup/restore timeout while communicating with the disk
Remedy:
Turn the product off then on and retry
Code: 32.1C.13
Display:
32.1C.13
Description:
Scheduled backup failure
Remedy:
Turn the product off then on and retry
Code: 32.1C.14
Display:
32.1C.14
Description:
NVRAM restore timeout while communicating with the formatter
Remedy:
Turn the product off then on and retry
Code: 32.1C.15
Display:
32.1C.15
Description:
NVRAM restore timeout while communicating with the finisher firmware
Remedy:
Turn the product off then on and retry
Code: 32.1C.16
Display:
32.1C.16
Description:
NVRAM restore timeout while communicating with the scanner firmware
Remedy:
Turn the product off then on and retry
Code: 32.1C.17
Display:
32.1C.17
Description:
NVRAM restore timeout while communicating with the engine
Remedy:
Turn the product off then on and retry
Code: 32.1C.18
Display:
32.1C.18
Description:
Backup of copy subsystem failed
Remedy:
Turn the product off then on and retry
Code: 32.1C.19
Display:
32.1C.19
Description:
Backup of fax subsystem failed
Remedy:
Turn the product off then on and retry
Code: 32.1C.1A
Display:
32.1C.1A
Description:
Backup of digital send subsystem failed
Remedy:
Turn the product off then on and retry
Code: 32.1C.1B
Display:
32.1C.1B
Description:
Backup of print subsystem failed
Remedy:
Turn the product off then on and retry
Code: 32.1C.1C
Display:
32.1C.1C
Description:
Backup of networking subsystem failed
Remedy:
Turn the product off then on and retry
Code: 32.1C.1D
Display:
32.1C.1D
Description:
Backup of finishing subsystem failed
Remedy:
Turn the product off then on and retry
Code: 32.1C.1E
Display:
32.1C.1E
Description:
Restore of copy subsystem failed
Remedy:
Turn the product off then on and retry If the error persists, clear the firmware image from the active partition by using the Partial Clean item in the Preboot menu.
Code: 32.1C.1F
Display:
32.1C.1F
Description:
Restore of fax subsystem failed
Remedy:
Turn the product off then on and retry If the error persists, clear the firmware image from the active partition by using the Partial Clean item in the Preboot menu.
Code: 32.1C.20
Display:
32.1C.20
Description:
Restore of digital send subsystem failed
Remedy:
Turn the product off then on and retry If the error persists, clear the firmware image from the active partition by using the Partial Clean item in the Preboot menu.
Code: 32.1C.21
Display:
32.1C.21
Description:
Restore of print subsystem failed
Remedy:
Turn the product off then on and retry If the error persists, clear the firmware image from the active partition by using the Partial Clean item in the Preboot menu.
Code: 32.1C.22
Display:
32.1C.22
Description:
Restore of networking subsystem failed
Remedy:
Turn the product off then on and retry If the error persists, clear the firmware image from the active partition by using the Partial Clean item in the Preboot menu.
Code: 32.1C.24
Display:
32.1C.24
Description:
NVRAM backup/restore successful
Remedy:
Turn the product off then on and retry.
Code: 32.1C.25
Display:
32.1C.25
Description:
Reset of copy subsystem failed
Remedy:
Turn the product off then on and retry.
Code: 32.1C.26
Display:
32.1C.26
Description:
Reset of fax subsystem failed
Remedy:
Turn the product off then on and retry.
Code: 32.1C.27
Display:
32.1C.27
Description:
Reset of digital send subsystem failed
Remedy:
Turn the product off then on and retry.
Code: 32.1C.28
Display:
32.1C.28
Description:
Reset of print subsystem failed
Remedy:
Turn the product off then on and retry.
Code: 32.1C.29
Display:
32.1C.29
Description:
Reset of networking subsystem failed
Remedy:
Turn the product off then on and retry.
Code: 32.1C.2A
Display:
32.1C.2A
Description:
Reset of finishing subsystem failed
Remedy:
Turn the product off then on and retry.
Code: 32.1C.2B
Display:
32.1C.2B
Description:
Reset formatter timeout
Remedy:
Turn the product off then on and retry.
Code: 32.1C.2C
Display:
32.1C.2C
Description:
Reset finisher timeout
Remedy:
Turn the product off then on and retry.
Code: 32.1C.2D
Display:
32.1C.2D
Description:
Reset scanner timeout
Remedy:
Turn the product off then on and retry.
Code: 32.1C.2E
Display:
32.1C.2E
Description:
Reset engine timeout
Remedy:
Turn the product off then on and retry.
Code: 32.1C.2F
Display:
32.1C.2F
Description:
Reset failure
Remedy:
Turn the product off then on and retry.
Code: 32.21.00
Display:
32.21.00
Description:
Corrupt firmware in external accessory
Remedy:
Turn the product off, then on, and retry. If the error persists, clear the firmware image from the active partition by using the Partial Clean item in the Preboot menu
Code: 33.01.01
Display:
33.01.01
Description:
A restore process has occurred.
Remedy:
No action necessary.
Code: 33.01.02
Display:
33.01.02
Description:
A save process has occurred.
Remedy:
No action necessary.

Code: 33.XX.YY
Display:
33.XX.YY Used board/disk
Description:
An encrypted board or disk with existing data previously locked to a different product has replaced the original. If you continue, data is permanently lost.
Remedy:
To save the data on the board or disk, turn the product off. Replace the board or disk with another board or disk. To delete the data on the board or disk and continue, touch the OK button.
Code: 40.00.01
Display:
40.00.01 USB I/O buffer overflow To continue, touch “OK”
Description:
The USB buffer has overflowed.
Remedy:
Touch the OK button to print the transferred data (some data might be lost). Check the host configuration.
Code: 40.00.02
Display:
40.00.02 Embedded I/O buffer overflow To continue, touch “OK”
Description:
The product has experienced a JetDirect buffer overflow.
Remedy:
Touch the OK button to print the transferred data (some data might be lost). Check the host configuration.
Code: 40.00.05
Display:
40.00.05 Embedded I/O bad transmission To continue, touch “OK”
Description:
The USB device has been removed.
Remedy:
Touch the OK button to clear the error message. (Data will be lost.) Install the USB device.
Code: 41.02.00
Display:
41.02.00 Error
Description:
A beam detected misprint error.
Remedy:
Turn the product off, and then on. If the error persists, replace the laser/scanner assembly.
Code: 41.03.YZ
Display:
41.03.YZ Unexpected size in envelope feeder To use another tray, touch "Options"
Description:
The product detected a different paper size than expected. - Y = 0 Size mismatch. Detected media is longer or shorter than expected. - Y = A Size mismatch. Detected media too long. - Y = B Size mismatch. Detected media too short. - Y = C Size mismatch. Inter-page gap error. - Z = D Source is duplexer - Z = E Source is envelope feeder - Z = 2 Source is Tray 2 - Z = 3 Source is Tray 3 - Z = 4 Source is Tray 4 - Z = 5 Source is Tray 5
Remedy:
Make sure that the feeder is loaded with the correct paper size and that the sliding paper guides are correctly adjusted. Use the Tray/Bin manual sensor test to verify that the envelope feeder paper sensor (PS1802) is correctly functioning. If the error persists, replace the envelope feeder.
Code: 41.03.YZ
Display:
41.03.YZ Unexpected size in tray
Description:
The product detected a different paper size than expected. - Y = 0 Size mismatch. Detected media is longer or shorter than expected. - Y = A Size mismatch. Detected media too long. - Y = B Size mismatch. Detected media too short. - Y = C Size mismatch. Inter-page gap error. - Z = D Source is duplexer - Z = E Source is envelope feeder - Z = 1 Source is Tray 1 - Z = 2 Source is Tray 2 - Z = 3 Source is Tray 3 - Z = 4 Source is Tray 4 - Z = 5 Source is Tray 5
Remedy:
Make sure that the tray is loaded with the correct paper size and that the sliding paper guides are correctly adjusted. Use the Tray/Bin manual sensor test to verify that the cassette media switch is correctly functioning. If the error persists, replace the lifter assembly.
Code: 41.05.YZ
Display:
41.05.YZ Unexpected type in tray
Description:
The product detected a different paper type than expected. - Y = 0 (expected type) Unknown - Y = 1 (expected type) Normal media - Y = 3 (expected type) LBP OHT - Y = 6 (expected type) Non-assured OHT - Y = 7 (expected type) Heavy media - Y = 8 (expected type) Light media - Y = 9 (expected type) Rough media - Y = C (expected type) Heavy media 3 - Y = D (expected type) Heavy media 2 - Z = 1 (detected type) Normal media - Z = 3 (detected type) LBP OHT - Z = 6 (detected type) Non-assured OHT - Z = 7 (detected type) Heavy media . Z = 8 (detected type) Light media - Z = 9 (detected type) Rough media - Z = B (detected type) Heavy glossy media (glossy media 2) - Z = C (detected type) Heavy media 3 - Z = D (detected type) Heavy media 2
Remedy:
Load the tray with the size and type of paper indicated, or use another tray if available. If this message appears and the tray is loaded with the correct paper type, check the print driver settings to make sure they match the tray type settings. Clean the Media Sensor. If the error persists, replace the paper pickup assembly.

Code: 41.XX.YZ
Display:
41.XX.YZ Error To continue, touch “OK”
Description:
A product error has occurred. - XX = error type - Y = fuser mode - Z = input tray - XX = 02 Beam detect misprint - XX = 09 Sub thermistor abnormally high - XX = 18 Scan line inclination adjustment - XX = 20 Image drum HV - Y = 2 Normal typed (not AutoSense) - Y = 3) Light media 1, 2, 3: typed or AutoSense - Y = 4 Heavy media 1: typed or AutoSense - Z = 0 Envelope feeder - Z = 1 Tray 1 - Z = 2 Tray 2 - Z = 3 Tray 3 - Z = 4 Tray 4 - Z = 5 Tray 5 - Z = 6 Tray 6 - Z = D Duplexer
Remedy:
Turn the product off, and then on. If the error persists, replace the DC controller PCA.
Code: 42.XX.YY
Display:
42.XX.YY
Description:
Internal system failure
Remedy:
Turn the product of,f then on, and retry. If the error persists, clear the firmware image from the active partition by using the Partial Clean item in the Preboot menu.
Code: 47.00.XX
Display:
47.00.XX
Description:
Back channel internal error
Remedy:
Turn the product off, and then on again. Resend the print job. If the error persists, execute the Partial Clean item in the Preboot menu.
Code: 47.01.XX
Display:
47.01.XX
Description:
Image transformer internal error
Remedy:
Turn the product off, and then on again. Resend the print job. If the error persists, execute the Partial Clean item in the Preboot menu.
Code: 47.02.XX
Display:
47.02.XX
Description:
Job parser internal error
Remedy:
Turn the product off, and then on again. Resend the print job. If the error persists, execute the Partial Clean item in the Preboot menu.e
Code: 47.03.XX
Display:
47.03.XX
Description:
Print job internal error
Remedy:
Turn the product off, and then on again. Resend the print job. If the error persists, execute the Partial Clean item in the Preboot menu.
Code: 47.04.XX
Display:
47.04.XX
Description:
Print spooler 9100 internal error
Remedy:
Turn the product off, and then on again. Resend the print job. If the error persists, execute the Partial Clean item in the Preboot menu.
Code: 47.05.00
Display:
47.05.00
Description:
Print spooler framework internal error
Remedy:
Turn the product off, and then on again. Resend the print job. If the error persists, execute the Partial Clean item in the Preboot menu.

Code: 47.06.XX
Display:
47.06.XX
Description:
Print App internal error
Remedy:
Turn the product off, and then on again. Resend the print job. If the error persists, execute the Partial Clean item in the Preboot menu.
Code: 47.WX.YZ
Display:
47.WX.YZ Printer Calibration Failed To continue, touch “OK”
Description:
The device is unable to access or implement one of the image patterns files. Y = calibration type, Z = event - 47.FC.20 (event code) Error Diffusion Image not found at system initialization - 47.FC.21 (event code) Error Diffusion Store image failure - 47.FC.22 (event code) Error Diffusion Image not found - 47.FC.23 Error Diffusion Print engine execution failure - 47.FC.300 (event code) Drum Speed Adjustment Image not found at system initialization - 47.FC.31 (event code) Drum Speed Adjustment Store image failure - 47.FC.32 (event code) Drum Speed Adjustment Image not found - 47.FC.33 (event code) Drum Speed Adjustment Print engine execution failure - 47.FC.40 (event code) Pulse Width Modulation Image not found at system initializatione - 47.FC.41 (event code) Pulse Width Modulation Store image failure - 47.FC.42 (event code) Pulse Width Modulation Image not found - 47.FC.43 (event code) Pulse Width Modulation Print engine execution failure
Remedy:
Turn the product off, and then on. If the error persists, reload the firmware.

热门图文

相关资料补充

HPM602N显示维护套件严重不足显示维护套件严重不足 技术论坛小马 鼓寿命到了.更换 手机用户..*.* 如何清零 技术 何厍 更换维护套件之后需要在机器的菜单中进行耗材重置的选择才能使用,以下是重置的方法:在机器“就绪”时,按一下菜...

Hp181fw出现代码55.0602错误 出现代码.错误,关闭然后打开,是什么原因?可以清除不,咋清除,如果要换配件,是哪个配件 引擎板与主板之间通讯错误 换主板 换了板好了 苏州售后维修电话,企业一站式服务,上...

»Hp181fw出现代码55.0602错误


热门关注
· hp laserjet m602常见故障代码描述,英文手册1

· hp laserjet m603常见故障代码描述,英文手册4

· hp laserjet m603常见故障代码描述,英文手册3

· hp laserjet m603常见故障代码描述,英文手册2

· hp laserjet m603常见故障代码描述,英文手册1

· hp laserjet m604dn常见故障代码描述,英文手册4

· hp laserjet m604dn常见故障代码描述,英文手册3

· hp laserjet m604dn常见故障代码描述,英文手册2

· hp laserjet m604dn常见故障代码描述,英文手册1

· hp laserjet m605dn常见故障代码描述,英文手册4

· hp laserjet m605dn常见故障代码描述,英文手册3

· hp laserjet m605dn常见故障代码描述,英文手册2

· hp laserjet m605dn常见故障代码描述,英文手册1

· hp laserjet m606dn常见故障代码描述,英文手册4

· hp laserjet m606dn常见故障代码描述,英文手册3

· hp laserjet m606dn常见故障代码描述,英文手册2

· hp laserjet m606dn常见故障代码描述,英文手册1

· hp laserjet m630dn常见故障代码描述,英文手册4

· hp laserjet m630dn常见故障代码描述,英文手册3

· hp laserjet m630dn常见故障代码描述,英文手册2

· hp laserjet m630dn常见故障代码描述,英文手册1

· hp laserjet m651dn常见故障代码描述,英文手册7

· hp laserjet m651dn常见故障代码描述,英文手册6

· hp laserjet m651dn常见故障代码描述,英文手册5

· hp laserjet m651dn常见故障代码描述,英文手册4

· hp laserjet m651dn常见故障代码描述,英文手册3

· hp laserjet m651dn常见故障代码描述,英文手册2

· hp laserjet m651dn常见故障代码描述,英文手册1

· hp laserjet m680dn常见故障代码描述,英文手册7

· hp laserjet m680dn常见故障代码描述,英文手册6

推荐文章
· hp2025颜色平面定位传感器错误

· hplaserjet9050dn错误代码49.2f83error

· hp2520hc电源灯闪并亮喊叹号

· hpm128fn加完粉后一直报黑色碳粉不足

· hpm202dw更换硒鼓出现不兼容的墨粉盒

· hpcp1025无法识别芯片

· hp128老提示更换硒鼓

· hp175a开机显示正在初始化后就显示通道卡纸

· hp1606dn提醒指示灯、就绪指示灯和“确定”指示灯亮起

· hpmfp175报49错误

· hplaserjetp1106就绪灯和错误灯同时亮

· hpn126打印机总是自动初始化

· hpm128fn双灯闪烁无显示

· hpm1136打印机激光器扫描架清理

· hpm1136mfp显示hp,然后下面两个灯一直在双闪,无法打印,什么情况

· hp5025错误代码59.20

· hp定影器错误关闭后然后打开

· hpm2727一直初始化

· hpcp5225恢复出厂设置

· hp177fw一体机新机提示安装成像鼓

· 佳能mf4452报警:e2020002接触式传感器hp错误,回路故障

· hp2055扫描打印复印一体机,显示printingdocument然后无反映故障

· hp1005纸刚出定影组件就卡住

· hp2055d开机提示52扫描仪错误

· hp128提示文档进纸器拾取错误

· hpm128fp故障灯一直闪控制面板无显示

· hp126nw提示正在使用用过的碳粉盒

· hpt790绘图仪错误代码79:03

· 79errorhp2600

· hp176开机时为什么电源灯旁的感叹号闪烁

· hpm1213nf打印一张通路卡纸

· hp1055cmip地址查询

· hp-mfpm176n加了粉还提示墨粉量低

· hp3630墨盒加墨水图解

· hp3035错误信息49.ff04

· hplaserjet1100serues显示感叹号

· hpm176一直提示三角感叹号错误是怎么回事

· hp1112开机灯闪烁

· hp系统错误7904关闭电源如果问题仍存在,请致电hp支持中心

· hpp2055d提示49err3d910c8怎么解决

· hpm1005复印薄的文稿有黑影

· hp226dw提示扫描仪错误17关闭然后打开

· hp1280电源灯不亮的真正原因

· hpp1606n不进纸,是什么问题

· hp2025彩色打印机报错59是哪里的问题

· ricohprintersc680

· hpm128fp开机一直显示正在初始化

· hp1319f屏幕 无显

· hp m1005一体机安装程序错误,rpc服务器不可用

· hp m1005 开机报scanner error 20错误,故障原因