hp 2840 Firmware Corrupt
更新时间：2024/3/18 2:18:12,view:628hp打印机HP 2840 Firmware Corrupt苏州hp复印机维修站电话0512-696l6769，苏州hpHP 2840 Firmware Corrupt维修站，hpHP 2840 Firmware Corrupt苏州维修站,hpHP 2840 Firmware Corrupt维修手册，hpHP 2840 Firmware Corrupt驱动程序下载，hpHP 2840 Firmware Corrupt说明书，hpHP 2840 Firmware Corrupt故障代码在线技术交流，有问必答,hpHP 2840 Firmware Corrupt小故障自己查询维修资料即可解决问题
hp Laserjet 2840 running via Mac OS X.
I was installing the firmware software from the hp site.
We had a power cut midway through installation, which did not finish.
I turned the machine back on, now it reads the error on the printer: 'Firmware Corrupt Ready 2 Download"
It wil not start and i cannot seem to get my laptop to see my printer and it will not restrat.
I have tried reinstalling, to no avail.
hp常见故障问题解答 2011-3-13 18:03:07
I am afraid you may have to replace the formatter. The service manaul makes note of a replacement firmware dimm but I do not think hp ever came out with it. The actual firmware chip is soldered on the formatter and I do not think there is a method to reflash the firmware when there is a power failure during upgrade. Only thing you may try which is a little trickey since you need a pc and I do not know if you can get the usb port to recongnize it with the firmware issue. If you can on the pc you would share the printer and then use the net use command to redirect lpt1 output to the usb port and then use a dos copy command to try and send the firmware upgrade to the printer. If you access to a pc and can get the computer to at least see the printer on usb report back for more detailed instructions.
hp常见故障问题解答 2011-3-13 18:03:27
Here are the instructions I found. Do not worry about the dates. If it does not work contact hp as they sold you the chip so they should be able to get it rectified.
Turn off the printer.
Open the memory access doors on the right hand side of the printer.
Insert the memory DIMM into the slot. Please notice the slots in the DIMM 'pins' match with the alignment features in the bottom of the DIMM slot in the printer. Small slot section is down.
After verifying that the DIMM is correctly in place, turn the printer On.
The printer will initially turn on and display Hewlett Packard on the LCD. After a short while the display will change to Erasing . After a short while, the display will change to Programming . The engine print cartridge carousel will be rotating during this time.
After a short while, the LCD will display complete : ) . The Ready LED will start flashing.
Turn Off the printer and remove the firmware recovery DIMM. Please recycle or dispose of the DIMM in accordance with local guidance. Do not return the DIMM to hp.
Power On the printer and wait until it is in a Ready state. Print a configuration test page by using the method describe in step one of this document.
Verify that the firmware datecode has been updated to 20050902.
top
If it works I would hold onto it or put it up on ebay as I am sure others could use it.
I was installing the firmware software from the hp site.
We had a power cut midway through installation, which did not finish.
I turned the machine back on, now it reads the error on the printer: 'Firmware Corrupt Ready 2 Download"
It wil not start and i cannot seem to get my laptop to see my printer and it will not restrat.
I have tried reinstalling, to no avail.
hp常见故障问题解答 2011-3-13 18:03:07 I am afraid you may have to replace the formatter. The service manaul makes note of a replacement firmware dimm but I do not think hp ever came out with it. The actual firmware chip is soldered on the formatter and I do not think there is a method to reflash the firmware when there is a power failure during upgrade. Only thing you may try which is a little trickey since you need a pc and I do not know if you can get the usb port to recongnize it with the firmware issue. If you can on the pc you would share the printer and then use the net use command to redirect lpt1 output to the usb port and then use a dos copy command to try and send the firmware upgrade to the printer. If you access to a pc and can get the computer to at least see the printer on usb report back for more detailed instructions.
hp常见故障问题解答 2011-3-13 18:03:27 Here are the instructions I found. Do not worry about the dates. If it does not work contact hp as they sold you the chip so they should be able to get it rectified.
Turn off the printer.
Open the memory access doors on the right hand side of the printer.
Insert the memory DIMM into the slot. Please notice the slots in the DIMM 'pins' match with the alignment features in the bottom of the DIMM slot in the printer. Small slot section is down.
After verifying that the DIMM is correctly in place, turn the printer On.
The printer will initially turn on and display Hewlett Packard on the LCD. After a short while the display will change to Erasing . After a short while, the display will change to Programming . The engine print cartridge carousel will be rotating during this time.
After a short while, the LCD will display complete : ) . The Ready LED will start flashing.
Turn Off the printer and remove the firmware recovery DIMM. Please recycle or dispose of the DIMM in accordance with local guidance. Do not return the DIMM to hp.
Power On the printer and wait until it is in a Ready state. Print a configuration test page by using the method describe in step one of this document.
Verify that the firmware datecode has been updated to 20050902.
top
If it works I would hold onto it or put it up on ebay as I am sure others could use it.
苏州hp售后维修站 互动 2011-3-13 18:03:27 Here are the instructions I found. Do not worry about the dates. If it does not work contact hp as they sold you the chip so they should be able to get it rectified.
Turn off the printer.
Open the memory access doors on the right hand side of the printer.
Insert the memory DIMM into the slot. Please notice the slots in the DIMM 'pins' match with the alignment features in the bottom of the DIMM slot in the printer. Small slot section is down.
After verifying that the DIMM is correctly in place, turn the printer On.
The printer will initially turn on and display Hewlett Packard on the LCD. After a short while the display will change to Erasing . After a short while, the display will change to Programming . The engine print cartridge carousel will be rotating during this time.
After a short while, the LCD will display complete : ) . The Ready LED will start flashing.
Turn Off the printer and remove the firmware recovery DIMM. Please recycle or dispose of the DIMM in accordance with local guidance. Do not return the DIMM to hp.
Power On the printer and wait until it is in a Ready state. Print a configuration test page by using the method describe in step one of this document.
Verify that the firmware datecode has been updated to 20050902.
top
If it works I would hold onto it or put it up on ebay as I am sure others could use it.
苏州hp售后维修站 互动 2011-3-13 18:03:07 I am afraid you may have to replace the formatter. The service manaul makes note of a replacement firmware dimm but I do not think hp ever came out with it. The actual firmware chip is soldered on the formatter and I do not think there is a method to reflash the firmware when there is a power failure during upgrade. Only thing you may try which is a little trickey since you need a pc and I do not know if you can get the usb port to recongnize it with the firmware issue. If you can on the pc you would share the printer and then use the net use command to redirect lpt1 output to the usb port and then use a dos copy command to try and send the firmware upgrade to the printer. If you access to a pc and can get the computer to at least see the printer on usb report back for more detailed instructions.
热门图文