苏州hp打印机维修服务网 > Printer Repair Data > Hp > 正文

hp4600 and 5500 Series Printers - 49.xxxx Errors

更新时间：2024/4/4 22:42:50,view:586

HP4600 and 5500 Series Printers - 49.xxxx Errors打印机苏州平望打印机售后服务中心电话0512-696l6769，苏州HP4600 and 5500 Series Printers - 49.xxxx Errors平望维修站，HP4600 and 5500 Series Printers - 49.xxxx Errors平望维修站, hp5200lx清零, hp227会自动打印乱码, hpm1005吃纸一张半, hp1020plus不上纸搓纸轮无反应, HP1025同时闪粉盒黑蓝红,

hp4600 and 5500 Series Printers - 49.xxxx Errors

The printer displays a 49.XXXX error on the control panel. 49.XXXX errors, including 49.FF04 , 49.FF07 , 49.FF08 , and 49.FF09 could be hardware or software errors. The error could be caused by third-party memory, improperly installed or third-party EIO devices or a specific print job and/or software application.
Determine if the error is software or hardware by resending any jobs in progress, sending a different job from another software application, or changing the size of the current job. If the error is still present with other applications or jobs, continue with the troubleshooting steps in the next section.
Troubleshooting steps
  1. Verify that the formatter light is blinking or steady. If the formatter is blinking, it is functioning properly and probably does not need to be replaced. If the formatter light is not blinking, proceed to Step 2.
  2. Turn off the printer and unplug the power cord.
  3. Remove the hp Jetdirect card, third-party device, hard disk, parallel cable, or IFR cable from the formatter if one is installed.
  4. If the error continues with accessories removed from the formatter, perform a cold reset on the printer. Ensure the hp Jetdirect card is not in the printer during a cold reset or the card settings will be changed back to default settings. To perform a cold reset, do the following:
    1. Turn on the printer.
    2. Watch the control panel.
    3. When the memory starts counting, press and hold the green (Select ) button.
    4. Continue holding the green check button until the Ready, Data, and Attention lights flash once, and then stay on steady.
    5. Release the check button when the Ready, Data, and Attention light are on steady.
      The control panel will display SELECT LANGUAGE .
    6. Press (Down Arrow ) button once. The control panel will display COLD RESET .
    7. Press (Select ). The printer will perform a cold reset and then continue its power-on sequence.
  5. If the printer comes up to ready, print a Configuration page. If a 49 error occurs from printing internal pages, continue on to the next step.
  6. Turn the printer off and unplug the power cord.
  7. Remove the eight screws around the formatter.
  8. Remove the formatter. See Figure 1.
  9. Reseat the firmware and memory modules on the formatter. Check for any DIMMs that are non-hp and remove them. Non-hp DIMMs are not supported by hp and may cause this error. Replace with hp DIMMs, if necessary.
  10. Reseat the daughter (interconnect) board. The daughter board is connected to the formatter behind EIO slot #1. To release the daughter board, push in the black retaining tab underneath the formatter (see Figure 1, call-out 1), then lift up the one side of the daughter board.
    Figure 1: Lifting up the daughter (interconnect) board on the formatter
    1 - Black retaining tab underneath the formatter
  11. Reseat the daughter board. See Figure 2.
    Figure 2: Reseating the daughter board
  12. Install the formatter.
  13. Turn the printer on again.
  14. If it comes up to READY , print a configuration page. If a 49 error does not appear from printing internal pages, or at power up, continue to the next step.
    NOTE: If a 49 error does appear when printing internal pages, call hp Customer Care for assistance.

    售后技术交流平台  2016-8-1 7:29:15 
     49网络板故障
  15. Install the hp Jetdirect card and hard disk before installing the formatter. Verify that each device is properly seated.
  16. Test any EIO devices, by turning off the printer, installing each device separately, and printing a Configuration page. Repeat for each EIO device.
  17. If the 49 error occurs with any EIO device installed, replace that EIO device.


    18. 售后技术交流平台  2016-8-1 7:29:15 
     49网络板故障

    热门图文

    相关资料补充


    最新文章