hp Laserjet 2200D Laser/Scanner Error Fix
更新时间：2024/3/25 8:41:13,view:575HP Laserjet 2200D Laser/Scanner Error Fix打印机苏州金鸡湖复印机维修服务中心电话0512-696l6769，苏州HP Laserjet 2200D Laser/Scanner Error Fix金鸡湖维修站，HP Laserjet 2200D Laser/Scanner Error Fix金鸡湖维修站, hp7110打印机维修, hp3630加墨, HP 5225如何恢复出厂设置, hpM403更改纸盒, hp1005故障代码17处理办法,
Just thought I would post these instructions since I was able to repair 2 laserjet 2200Ds during the past week using a method Moe had once mentioned. The symptons on the machines were a bit different but the error message was the same. When you sent a print document the machine would start to warm up and then all three light would come on solid. Pressing the job cancel and go buttons at the same time would result in only the middle led staying on solid which is a 52 laser/scanner error. In both case the motor in the laser/scanner was the culprit. With the cost of a new laser/scanner being about 200.00 it is really not economical to replace the part. What I did was the following. I removed the right side cover by pressing down on the button below the top cover and moving the cover towards the front and out. Next I lowered the back face up tray and released the two holding clips one on each side so the tray would go all the way down and removed the two screws which secures it to the frame. I then pulled out from the left side when looking from the rear and released the small clip on the right side and off it comes. I then removed the two screws one on each side in the back which secures the top cover. I next removed the two screws in the front under the toner door one on each side which hold the cover in the front. I then released the toner cam plastic piece on the right side which raises with the toner door. All you do is press together the plastic piece which goes thru the hole and slde the clip to the right and push it down into the down cover. Now just release the small holding clip on the left side under the toner door and you can lift the top cover off. Once the cover is off, you now have access to the laser/scanner which is the black box in the middle rear. Remove the multicolored wire on the right side from the circut board and release from the two clips on top of the laser/scanner and lay it over the left side. Now remove the purple wire connector from the same board which goes to the two wire harnesses on the laser scanner. Remove the one end of that same cable from the front right side connector on the top and release both parts of the wire from the holding clip on the top of the laser/scanner. Now remove the six black screws which hold the top of the laser/scanner cover and remove the cover. In the back of the laser/scanner is the motor assembly which the other part of the purple wire harness goes to. Remove the four screws which hold the motor and circut board and remove the motor and circut board. You may have to apply a bit of upward pressure to get it to come out, but it will come out. Now looking at the chrome motor cover at the bottom is a small plastic piece which holds the cover in place and prevents it from coming off. Squeeze the plastic piece together with a small needle nose pliers and remove. Now you can remove the motor cover and shaft. Put a couple of very small drops of light machine oil down into the exposed shaft of the motor assembly. Just a little since you donot want to fill the shaft all the way to the top. Put the cover and shaft back and put the plastic holding piece back in place. While you have the top cover open you may want to use a q-tip to clean all the optics playing most attention to the mirror assembly in the front. Now reverse these instructions and put everything back together and hopefully you will be back in business. The only thing which can be tricky is the toner cam shaft plastic piece. The best way is to close the toner door and put the cover on all the way and then raise the right side of the top cover a bit and raise the plastic piece up so you can put the shaft of it into the hole of the cover hindge piece. I figure having 2 successes in one week is worth posting instructions. Let me know if it works for anyone out there.
hp常见故障问题解答 2010-3-27 20:55:14
I would just like to add something from experience. After you are done with the oil, the centrifical force will fling the oil out if you put too much on it. You might want to put a folded paper towel in front of the prism the first time you spin the scanner up. This will catch the oil that gets thrown out. I ruined a prism the first time I did one.
hp常见故障问题解答 2010-3-27 20:55:14
I would just like to add something from experience. After you are done with the oil, the centrifical force will fling the oil out if you put too much on it. You might want to put a folded paper towel in front of the prism the first time you spin the scanner up. This will catch the oil that gets thrown out. I ruined a prism the first time I did one.
hp常见故障问题解答 2010-3-27 20:55:14 I would just like to add something from experience. After you are done with the oil, the centrifical force will fling the oil out if you put too much on it. You might want to put a folded paper towel in front of the prism the first time you spin the scanner up. This will catch the oil that gets thrown out. I ruined a prism the first time I did one.
hp常见故障问题解答 2010-3-27 20:55:14 I would just like to add something from experience. After you are done with the oil, the centrifical force will fling the oil out if you put too much on it. You might want to put a folded paper towel in front of the prism the first time you spin the scanner up. This will catch the oil that gets thrown out. I ruined a prism the first time I did one.
苏州hp售后维修站 互动 2010-3-27 20:55:14 I would just like to add something from experience. After you are done with the oil, the centrifical force will fling the oil out if you put too much on it. You might want to put a folded paper towel in front of the prism the first time you spin the scanner up. This will catch the oil that gets thrown out. I ruined a prism the first time I did one.
热门图文