hp9800 Deskjet Printer Lights ERROR

更新时间:2024/3/19 11:47:48,view:455

HP9800 Deskjet Printer Lights ERROR打印机苏州吴中复印机维修站电话0512-696l6769,苏州HP9800 Deskjet Printer Lights ERROR吴中维修站,HP9800 Deskjet Printer Lights ERROR吴中维修站,HP9800 Deskjet Printer Lights ERROR维修手册,HP9800 Deskjet Printer Lights ERROR驱动程序下载,HP9800 Deskjet Printer Lights ERROR说明书,HP9800 Deskjet Printer Lights ERROR故障代码在线技术交流,有问必答,HP9800 Deskjet Printer Lights ERROR卡纸,打印浅,亮红灯,不通电,无法使用等故障自己查询维修资料即可解决问题

 hp-9800 Deskjet is causing me MAJOR grief.
Immediately from powering it on (plugging it in) here is what it does.
1) The printer lights strobe from the left printer cartridge light, to the right printer cartridge light, then to the resume light & then to the power button light. This goes on for about 15 seconds (again lights left to right).
2) Then the printer heads goes all the way across to the left and then the right?then it ejects a black sheet of paper. (I noticed the printer head kinda slaps against both ends of the carriage (as if it doesn抰 know where the end of the carriage is).
3) Then both left and right printer cartridge lights light up and stay on continuously & the resume and power lights blink back and fourth.

I tried to diagnose the lights this with hp's Help file but I don't see anything quite like this.

What I have done so far. Replaced both cartridges color (97) & black(96) with brand new ones. Looked for paper jam but nothing.
I can never connect to the printer since it never is available
Blown out the inside with compressed (air in a can).
I cannot get anything disgnostic through the USB port since it never goes online to the computer. (I assume because its some sort of hardware error).

Thinking back... This problem was at 1st intermittent and could be cleared by a reset. Now its all the time!

THanks so much for your time and help
hp常见故障问题解答  2010-3-21 15:34:10 
 Service station stall. The service station is bound up or the timing disc is damaged or dirty, the sensor that detects the disc motion may be bad or dirty.
Left and right print cartridge lights.
The left print cartridge light indicates tri-color print cartridge status; the right print cartridge light indicates black or photo print cartridge status.
The print cartridge lights can be on or blinking in combination with the Power light and Resume light behaviors listed in this table.
On: Print cartridge is low on ink or out of ink. Replace the print cartridge soon. See Installing or replacing the print cartridges.
Blinking: Print cartridge is damaged, missing, or incompatible. Reinstall or replace the print cartridge. See Installing or replacing the print cartridges. If printing with a single print cartridge, ignore this light.
Printer lights cycle.
The printer lights cycle when the printer is reinitializing.
No action required.
Power light on.
Printer is turned on and idle.
No action required.
Power light blinks.
Printer is printing or processing a print job.
No action required.
Power light blinks twice, stays off, then repeats the pattern.
Printer is cancelling a print job.
No action required.
Power light on, Resume light blinks.
Check for one of the following conditions:
Printer is waiting for special media to dry. Press the Resume button if you do not want to wait. You can change the dry time in the printer driver. See Ink is smearing .
Printer is out of paper. Load paper and press the Resume button to continue the print job.
There is a media/banner size mismatch. Make sure the media/banner size selected in the printer driver matches the media/banner size loaded in the printer. To eject the media/banner, press the Resume button.
I/O stall. Make sure your system is running properly and the printer is properly connected to your system. Turn off the printer, and then turn it on again. Then resend the print job. To check the system, see the guidelines in Troubleshooting .
Power light off, Resume light blinks.
Paper motor stall.
Clear the jammed paper. See Clearing jams. After clearing the jam, press the Resume button to continue the print job.
If no paper jam exists, press the Resume button. If this does not work, turn off the printer, and then turn it on again. Then resend the print job.
Power and Resume lights blink together at same time.
Carriage stall.
If there is a paper jam, clear the jammed paper. See Clearing jams. After clearing the jam, press the Resume button to continue the print job.
If no paper jam exists, press the Resume button. If this does not work, turn off the printer, and then turn it on again. Then resend the print job.
Power and Resume lights blink, Left and right print cartridge lights on.
Service station stall.
Open the top cover and unplug the power cord. Wait for the Resume and Power lights to go off. Close the top cover and plug in the power cord. Wait for the printer to reinitialize and resend the print job.
All printer lights blink together.
Hardware error.
Make sure there is no paper jam in the printer. See Clearing jams.
If you cannot resume the print job, cancel the print job. Turn off the printer, turn it back on, and then try to print again. If the problem persists, turn off the printer and disconnect the cable from the printer. Reconnect the cable, turn on the printer, and then try to print again.
Power and Resume lights on.
Check for one of the following conditions:
Make sure the top cover is closed.
Make sure the rear access panel or duplex unit is correctly installed and locked into place.
Left print cartridge light on, Power light on.
Tri-color print cartridge is low on ink or out of ink.
Reinstall or replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Right print cartridge light on, Power light on.
Black or photo print cartridge is low on ink or out of ink.
Reinstall or replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Left and right print cartridge lights on, Power light on.
The left (tri-color) and right (black or photo) print cartridges are both low on ink or out of ink.
Reinstall or replace the print cartridges. See Installing or replacing the print cartridges.
Left print cartridge light blinks, Power light on.
Tri-color print cartridge is damaged or missing.
Reinstall the print cartridge. If the error persists, replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Right print cartridge light blinks, Power light on.
Black or photo print cartridge is damaged or missing.
Reinstall the print cartridge. If the error persists, replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Left and right print cartridge lights blink, Power light on.
The left (tri-color) and right (black or photo) print cartridges are both damaged or missing.
Reinstall the print cartridge. If the error persists, replace the print cartridge. See Installing or replacing the print cartridges.



售后技术解答  2010-3-21 15:34:10 
 Service station stall. The service station is bound up or the timing disc is damaged or dirty, the sensor that detects the disc motion may be bad or dirty.
Left and right print cartridge lights.
The left print cartridge light indicates tri-color print cartridge status; the right print cartridge light indicates black or photo print cartridge status.
The print cartridge lights can be on or blinking in combination with the Power light and Resume light behaviors listed in this table.
On: Print cartridge is low on ink or out of ink. Replace the print cartridge soon. See Installing or replacing the print cartridges.
Blinking: Print cartridge is damaged, missing, or incompatible. Reinstall or replace the print cartridge. See Installing or replacing the print cartridges. If printing with a single print cartridge, ignore this light.
Printer lights cycle.
The printer lights cycle when the printer is reinitializing.
No action required.
Power light on.
Printer is turned on and idle.
No action required.
Power light blinks.
Printer is printing or processing a print job.
No action required.
Power light blinks twice, stays off, then repeats the pattern.
Printer is cancelling a print job.
No action required.
Power light on, Resume light blinks.
Check for one of the following conditions:
Printer is waiting for special media to dry. Press the Resume button if you do not want to wait. You can change the dry time in the printer driver. See Ink is smearing .
Printer is out of paper. Load paper and press the Resume button to continue the print job.
There is a media/banner size mismatch. Make sure the media/banner size selected in the printer driver matches the media/banner size loaded in the printer. To eject the media/banner, press the Resume button.
I/O stall. Make sure your system is running properly and the printer is properly connected to your system. Turn off the printer, and then turn it on again. Then resend the print job. To check the system, see the guidelines in Troubleshooting .
Power light off, Resume light blinks.
Paper motor stall.
Clear the jammed paper. See Clearing jams. After clearing the jam, press the Resume button to continue the print job.
If no paper jam exists, press the Resume button. If this does not work, turn off the printer, and then turn it on again. Then resend the print job.
Power and Resume lights blink together at same time.
Carriage stall.
If there is a paper jam, clear the jammed paper. See Clearing jams. After clearing the jam, press the Resume button to continue the print job.
If no paper jam exists, press the Resume button. If this does not work, turn off the printer, and then turn it on again. Then resend the print job.
Power and Resume lights blink, Left and right print cartridge lights on.
Service station stall.
Open the top cover and unplug the power cord. Wait for the Resume and Power lights to go off. Close the top cover and plug in the power cord. Wait for the printer to reinitialize and resend the print job.
All printer lights blink together.
Hardware error.
Make sure there is no paper jam in the printer. See Clearing jams.
If you cannot resume the print job, cancel the print job. Turn off the printer, turn it back on, and then try to print again. If the problem persists, turn off the printer and disconnect the cable from the printer. Reconnect the cable, turn on the printer, and then try to print again.
Power and Resume lights on.
Check for one of the following conditions:
Make sure the top cover is closed.
Make sure the rear access panel or duplex unit is correctly installed and locked into place.
Left print cartridge light on, Power light on.
Tri-color print cartridge is low on ink or out of ink.
Reinstall or replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Right print cartridge light on, Power light on.
Black or photo print cartridge is low on ink or out of ink.
Reinstall or replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Left and right print cartridge lights on, Power light on.
The left (tri-color) and right (black or photo) print cartridges are both low on ink or out of ink.
Reinstall or replace the print cartridges. See Installing or replacing the print cartridges.
Left print cartridge light blinks, Power light on.
Tri-color print cartridge is damaged or missing.
Reinstall the print cartridge. If the error persists, replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Right print cartridge light blinks, Power light on.
Black or photo print cartridge is damaged or missing.
Reinstall the print cartridge. If the error persists, replace the print cartridge. See Installing or replacing the print cartridges.
You can still print with one print cartridge. See Printing with a single print cartridge.
Left and right print cartridge lights blink, Power light on.
The left (tri-color) and right (black or photo) print cartridges are both damaged or missing.
Reinstall the print cartridge. If the error persists, replace the print cartridge. See Installing or replacing the print cartridges.

热门图文

相关资料补充


最新文章
· canon mp140 printer problem

· canon laser class 8500 will not fax out.

· canon mp730 paper extra feeds

· samsung ml-2851ndr reset counter of prints

· hp deskjet 5440 printer in put tray pn

· hp officejet d145 scanner failure

· epson 2200 cleaning

· canon i850 light flashing orange

· epson aculaser c1100 error message "service req e511"

· epson 740 (circa. 1999) sqeals like cats fightng

· epson stylus color 3000 driver for mac os 10.5

· brothers mfc-210c removing the print head?

· e260 toner patch sensor

· lexmark x2230 will not attach with my laptop.

· canon mp370 waste ink full

· epson stylus cx5400, now scanner error changed ink

· lexmark e260dn toner encoder question

· olivetti pr2 plus passbook printer service manual and drivers. where can i found it? pls help me...

· hp 2200d had a horrible "squeal"

· samsung clp-510 - duplex pages out of order!

推荐文章
· problem with canon ip4300

· canon waste ink full reset

· hp lj 8100dn jams when printing to top bin

· panasonic kx-p4410 message 'call service e31'

· epson epl-n2050 error e030

· hp 845c troubles - head just keeps scrolling

· epson r1800 lights flashing

· samsung ml-4600 paper jams

· hp laserjet 1300 prints smiley/square every few min

· hp 4200 printing light after maint. kit

· hp5150 mechanism error

· lexmark m 410 load letter paper

· epson c43 maintenence

· epson 777 - won't print test page

· lexmark optra t 620 tray 3 jam

网友热门关注
· hp laserjet 5 horizontal lines-left side of paper

· hp photosmart c3180 problem with refill

· canon mp830 purge unit sticking

· waste ink pad replacement

· samsung clx-3175 reset chip / toner

· samsung ml-1640 reset

· hp psc 1610 always out of paper

· hp psc 750 disassembly?

· epson sx 115 cartridge not recognize ?

· canon ip4000 five flash problem.

· lexmark c510, vertical streaks in printouts

· reset epson t50 and t60 without error 21000068

· canon pixma mp780 error ##356

· canon ip2600 reset

· brother mfc 240c error code 51 - unable to print

· samsung clp 315,ml 1640prineter chip reset

· epson r1800 erroneous paper jam error

· open epson stylus c62 to replace waste pads

· canon d320 fuser heat sleeve

· paper jam error pixma mp150

· canon ip3000 print head carriage jammed

· hp lj 2300 error 52.00 after different cartridge

· how do i clean canon mp450 waste ink absorber error code 5800?

· error u051: canon pixma mp470

· hp lj 4si vertical streaks lines

· epson photo 2100 all lights flashing.

· samsung ml-2850 toner refill

· hp laserjet 3800dn 10.92.03 cartridges not engaged error.

· how to access canon mp 830 scanner lamp

· hp laserjet 4250 duplexer causing occasional creases

· epson picturemate general error (0002)

· hp psc 1510 paper feed problem

· very strange hp4550 error

· xerox phaser 7700 fuser problem?

· canon pixma mp198 waste ink pad full

· hp photosmart 8250 error code 0xc18a0001

· hp 4015 service code required

· brother dcp 130c unable to clean 46

· epson c45 replace / clean waste ink pads

· canon pixma mp160 printing problems

· samsung clp-300 - imaging unit problem

· hp 3500 - 59.99 error

· samsung clx-3175 need reprogramming, please help:)

· canon pixma mp190 - paper pulls to one side and ja

· canon mp750 lost all power

· canon mp460 error 5100

· hp officejet k60 alignment failed /no yellow color

· epson stylus photo r300

· printing problem epson styllus tx700w

· unable to connect imac to epson px710w wirelessly

· how do i dismantle my canon ip4500?

· canon i865 prints poor & green

· xerox n2125 fuser repair.

· hp laserjet p4014n very irritating problem

· canon mp830 smudged wet print

· hp c6180 hard reset procedure

· canon pxma mp480 will not turn on

· hp 2430 is printing light on the left side the paper ..

· lexmark optra t614 -900 service rip software

· canon mp160 mp190 general tool

· hp officejet series 7210/7310/7410

· 41.3 unexpected paper size on a hp4050

· hp 9000 13.20.00 paperjam error

· hp color lj 3600n printer error 59.c0

· hp laserjet 4m plus error message 43.1 paper error

· samsung clp-300 jamming all the time

· epson stylus c90 (red light continuously blinks)

· hp office jet pro l7680 printing problems

· canon pixma mp780 - 3e cartridge and auto align

· hp officejet j4580 paper jam message

· brother 8660 dn low toner light with recent fill

· hp 8100 - frequent new fuser needed.

· hp lj 4345 printer problem

· hp 5610 carriage jam (loose parts found)

· canon ip1500 appropriate print head not installed

· canon i450 - will not print in black or blue

· hp laserjet 4050 fuser issue

· hp 2500 imag problem

· canon i860 blue line in photos

· hp laserjet 5l drivers for xp

· canon ipf8000 and drop out......

· hp laserjet 5m - blank print

· epson printer came out all light and blue and very unclear

· hp 940c parts view

· brother mfc 9420 reset "unable to print"?

· canon pixma ip 6000d clogged inkjet

· konica minolta 2480mf / win 7 - 64 bit driver

· canon i80 empty the excess ink tank

· hp x1100 series code 2170

· lexmark e240 - paper stops under the flap

· canon i70 printer problem

· hp designjet 130 error 3 symbols

· hp deskjet 1220 manual

· lexmark t644 print server problem

· epson px800fw - new pads only 4 months old

· lexmark 5600-6600 ink cartridges.

· illusory paper jam in samsung scx 4216

· hp laserjet 4350 printing veritcal white void.

· brother dcp-9045 cdn end of drum life override