佳能MP145/MP160 故障维修代码(英文版)

 CANON RESETTERCanon MP160 , MP145:) :) :) :)
1) With the printer powered off but connected to a power source, press the Power button while pressing and holding
the Stop/ Reset button.
2) When the Power is lit, press the Stop/Reset button two times while pressing and holding the Power button.
3) When releasing the Power button and the Stop / Reset button (regardless of order), the printer will move into a
service mode. (Waiting for menu selection)
4) When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the
function listed in the table below.(Each time the Stop/Reset button is pressed, the LED lights alternately in
orange and green, starting with orange.)note: press 4 times for waste ink counter reset.

The number of the Reset
button pressing
LED Function Remarks
0 time Green Power off

1 time Orange Service pattern print
2 times Green EEPROM print
3 times Orange EEPROM reset
4 times Green Waste ink counter reset

5) Unplug cable power. (for MP145 / MP150)
6) Turn Off Power. (for MP160)

Error Code :
E2-2 = No paper (ASF)
E3-3 = Paper jam
E4 = No ink
E5-5 = The ink cartridges are not installed or a non-supported ink cartridge is installed, or the ink cartridges are not installed properly
E8 = Waste ink absorber full, or platen waste ink absorber full
E9 = The connected digital camera / video camera does not support Camera Direct Printing
E14 = The Ink cartridges whose destination are wrong
E15 = Ink cartridge is not installed E16 - Ink remaining is unknown
E16 -E19 = Failed to scan head alignment sheet
E22 = Carriage error
E23 = Paper feed error
E24 = Purge unit error
E25 = ASF(cam) sensor error
E26 = Internal temperature rise error
E27 = Waste ink absorber full or platen waste ink absorber full
E28 = Ink cartridge temperature rise error -
E29 = EEPROM error
E33 = Paper feed position error
E35 15 = USB Host VBUD overcurrent error - USB
E37 17 = Abnormal motor driver error
E40 20 = Other hardware error
E42 22 = Scanner error

更新时间:2022/7/28 7:29:34,view:2008



热门文章 20 篇
· 松下kx-f190cn型传真机不能复印、发送
· 夏普复印机消耗品规格表
· 松下uf-208m型传真机不能传真
· 松下kx-f828cn型传真机液晶屏显示“prper jam”
· 松下kx-f828cn型传真机无拨号音
· 松下kx-f828cn型传真机文稿不走纸
· 松下kx-f828cn型传真机接收步进电动机不转
· 松下kx-f828cn型传真机机器不动作
· 松下kx-f828cn型传真机复印件全黑
· 松下kx-f828cn型传真机复印件全白
· 松下uf-208m型传真机复印件有黑条
· 松下kx-f828cn型传真机不工作
· 松下uf-208型传真机液晶屏显示代码“004”
· 松下kx-90b型传真机话机和免提均听不到拔号音
· 松下kx-90b型传真机话机不起作用
· 松下kx-50b型传真机收、发电动机均不转
· 松下kx-50b故障维修实例
· 松下kx-50b型传真机记录纸阻塞
· 佳能传真机复杂故障
· 佳能维修事例篇

最新文章 20 篇
· 三星ml-2010 自检打印每次搓纸轮转半圈就卡纸,什么问题?
· 南天pr2打印机光敏参数设置方法
· 爱普生lq300k和lq-630k主板不联机维修经验总结及注意事项
· 佳能 s4500 开机叫8次, 黄灯闪8次,解决方法
· 联想lj6000加粉,方正a6100加粉,实战经验分享
· 东芝358 提示f10,是什么意思?
· 东芝163的复印机 出现c44,解决方法
· 东芝168s 出现c26代码,开机暴光灯能亮,求助?
· 东芝358 进纸错误,两个纸合都一样的问题?
· 东芝163 换载体后复印1千张左右颜色淡,是什么原因?
· 东芝163 复印a3纸,纸尾刚过热辊就不动了,代码e02 ,是什么问题?
· 施乐420 复印出来纸上有点黑,背面有一条浅黑道,是什么原因?
· 施乐518 开机复印两三张就不能复印了,关机后再开又能打两三张,why?
· 施乐420 为什么1-20分钟之间复印出来全部是黑的,为什么?
· 佳能 pixma ip2000 废墨满解码方法