HP LaserJet Error Codes and Service errors

http://www.oesell.com  来源:oesell.com  选稿:admin  文字大小:


02 WARMING UP (>3 MIN)
1. Remove I/O cables. (Cable is hooked up incorrectly or bad interface in computer.)
2. Formatter PCA malfunction.
3. DC Power Supply malfunction.
2686 Only:
1. DC Power Supply/Main motor driver malfunction.
IIISi/4Si Only:
1. Defective display cable, display, or Formatter PCA.

11 PAPER OUT
1. Paper tray empty or not seated correctly.
2. Paper Control PCA malfunction.
3. Sensor arm stuck or broken.

12 PRINTER OPEN
1. The printer door/lid is open.
2. Check DC Power Supply voltages or replace DC Power Supply.
3. DC Controller malfunction.
4. Tab missing on top cover.
5. 220V unit plugged into 110V outlet.
IIISi/4Si Only:
1. Check that PS1 is blocked by the latch flag. Replace PS1 if defective.
2. Check to see if fuser bulb turns on. If the fuser does not turn on check SW101.
3. DC Controller PCA malfunction.
4/4M/4+/4M+ Only:
1. Plunger missing on top cover.
2. Paper Control PCA malfunction.
4V/4MV Only:
1. Front Door-open Sensor (PS402) broken or stuck.
2. Toner cartridge microswitch (SW501 on High Voltage PCA) malfunction.
3. DC Controller PCA malfunction.


12 OPEN or NO TONER or NO EP
IIP/IIP+/IIIP Only:
1. Paper path door open.
2. No toner cartridge or cartridge not seated.
3. Defective fan, PS4 or PS5
4. External fuser access door not closed.
4P/5P Only:
1. Top cover open.
2. No toner cartridge.
3. Defective Interlock Switch Assembly.
4/4M/4+/4M+ Only:
1. Top cover open.
2. Defective Paper Control PCA on the Paper Feed Assembly.
4L Only:
1. The part of the top door that pushes the Plunger down is broken.

13 PAPER JAM
2686 Only:
1. Broken separation belt.
2. Paper path rollers worn?

a. Check paper pickup rollers.

b. Check paper feed roller.

c. Check transfer guide assembly.
3. Paper pickup clutch turning more than once?

a. Disassemble clutch and re-grease. Note 2686D: If one clutch needs re-greasing it is likely that they all do.
4. Bad registration sensor or bad fuser exit sensor.
II, III Only:

If no jam visible:
1. Replace cable, fuser to DC Controller (P/N RG1-0907-000)
II, IID, III, IIID Only:
1. Obstruction in paper path.
2. Out of spec media.
3. Replace or clean Pickup roller.
4. Replace Registration Assembly.
5. Replace fuser.
IID, IIID Only:
1. Check duplex paper path for obstructions.
2. Misadjusted or bent Switchback Assembly.
IIP, IIP+, IIIP Only:
1. Bad Paper Input sensor (PS1).
2. Bad fuser Exit Sensor (PS3).
5Si Only:
1. Paper is jammed somewhere in the paper path or a sensor flag is stuck.

13.X PAPER JAM
IIISi/4Si Only:
13.1 Internal - Check registration area, fuser exit sensor flag and sensor.
13.2 Input - Check paper input section and paper refeed from duplex unit.
13.3 Duplex - Check PS4 or PS5 in duplex or switchback, respectively.
13.4 Output - Check PS7 in output area.

5Si Only:
13.1 Paper late jam at PS2.
13.2 Paper late jam at PS1 registration photosensor.
13.3 Paper late arriving late at PS1403.
13.4 Paper jam in fuser.
13.5 Paper late jam at PS1402 face-down delivery photosensor.
13.6 Paper jam in face-down output.

4000/4050/4100/5000 Only:
13.1 Paper delay jam at feed area.
13.2 Paper stopped jam at paper feed area. Check PS102 and PS103
13.5 Paper delay jam at fuser. Check tansfer roller. Check PS501 and PS106 (only on the Laserjet 4100)
13.6 Paper stopped jam at fuser.
13.10 Paper jam in Duplexer. Check PS701 and PS703
13.20/13.32 Paper stopped jam in paper path. Check entire paper path, check all sensors and flags.
13.21/13.33 Door open jam.

8000/8100 Only:
13.1 Paper late jam at PS2.
13.2 Paper delay jam at PS1
13.5 Fuser output, paper late jam
13.6 Fuser output, paper stop jam.
13.9 Face down delivery, paper late jam
13.20 Engine could not eject jam from printer
13.A Paper stopped at the face down bin.

14 NO TONER CARTRIDGE
1. No toner cartridge installed.
2. Check tabs on side of toner cartridge. At least one of two tabs must be present.
3. Replace Paper Control PCA (Solenoid/Sensor PCB Assembly).
4. Replace DC Controller PCA.
2686 Only:
1. Bad cassette microswitch.
2. Check tabs on side of toner cartridge. At least one of two tabs must be present.
IIISi/4Si Only:
1. Install new toner cartridge.
2. Check tabs on side of toner cartridge. At least one of two tabs must be present.
3. Check Drum Sensitivity microswitches. Replace if either is bad.
4. Replace DC Controller PCA.

16 TONER LOW
1. Replace toner cartridge.
2. Replace high-voltage Power Supply.
II,III Only:
1. Replace Cable, DC Controller to H.V. Power Supply (P/N RG1-0906- 000).
IIISi/4Si Only:
1. Check Door Open sensor flag. Replace PS1 if defective.
2. Inspect toner level sensor connector for damage.
4. Replace DC Controller PCA.
5. Replace High-Voltage Power Supply.

20 ERROR/MEM OVERFLOW/INSUFFICIENT MEMORY
1. Add memory or simplify print job.

21 ERROR/PRINT OVERRUN/PAGE TOO COMPLEX
1. Simplify print job.
2. For LJ III, IIID, IIIP, IIISi/4Si with 1 MB extra memory, enable page protect.

22 ERROR/ I/O CONFIG ERROR
1. I/O config for the computer or printer is incorrect.
2. Wrong I/O cable.
3. Computer power is off.

23 I/O NOT READY
1. I/O card is unable to accept data or is not connected to the network.

30 PS ERROR XX
1. PCL file being sent to printer while in PostScript mode.
2. Check PostScript ROMs.

40 ERROR (DATA TRANSFER ERROR)
1. Computer and printer may be set to different baud rates.
2. Computer is powered off.
3. Conection has been broken between printer and EIO/MIO card; try reseating EIO/MIO card

40.X Mio Error
5Si Only:
40.1 HP Mio port 1 (upper slot)
40.2 HP Mio port 2 (lower slot)

41 ERROR (Temporary Beam Detect Error)
1. Reset by pressing the continue key.
2. See error 51.
IIP Only:
1. See Service Note 33471A-02B if Serial No. is between 2925J00000 to 3047J999999. (2-diode to 3-diode upgrade corrects static caused problem.)
IIP, IIP+, IIIP Only:
1. This error can be caused by Paper Feed problems.

41.1 or 2 Error or 41.3 Error
All Printers
There is a paper multifeed or the wrong size of paper is being used
5Si Only:
A temporary, non-fatal printing error occurred.
41.1 General misprint error.
41.2 Beam detect malfunction.
41.3 Improper paper size.
41.4 No video sync.
41.5 Noisy video sync req signal.

4000/4050/4100/5000/8000/8100 ONLY:
A temporary, non-fatal printing error occurred.
41.1 Unknown misprint error.
41.2 Beam detect malfunction.
41.3 Improper paper size.
41.4 No vsync error.
41.5 Media feed error.
41.9 Noisy video sync req signal.

42 OPT INTERFACE
1. Check installation of optional I/O card, reseat if necessary.
2. Optional I/O card is not connected to an active LAN.
3. Replace optional I/O card.

43 OPT INTERFACE
1. Same as 42 error.

49 FIRMWARE ERROR
Only for the laserjet 4100: Try printing a different file if error persists remove all dimms and EIO devices, last replace formatter.

50 ERROR

(Note: The printer must be powered off for at least 20 minutes to clear an error 50.)
2686 Only:
1. Bad 47W resistor (1/4W) on the Fuser Safety PCA (connector J107 on the Fuser Safety PCA). (P/N FF1-3872-000.)
2. Bad fuser bulb.
3. Bad Fuser Safety PCA. (P/N RG1-0208-030.)

Note 2686A/D: Short resistor R250 on the DC Controller to bypass error 50 time delay. Short the pin closest to the front of the printer. (The printer must be turned off.)
II, IID, III, IIID Only:
1. Replace fuser.
2. Replace AC Power Module.
3. Replace DC controller.

Note II: Short C211 on the DC Controller to bypass Error 50 time delay. (The printer must be turned off.)

Note IID: Short C216 on the DC Controller to bypass error 50 time delay. (The printer must be turned off.)
II,III Only:
1. Replace cable, Fuser to DC Controller, connector J206. (P/N RG1-0907-000.)
2. Replace cable, AC Power Module to DC Controller, connector J208. (P/N RG1-0912-000.)
IIP, IIP+, IIIP Only:
1. See Service Note 33471-01B if Serial No. is between 0000J00000 and 2949J2222
2. Replace Fuser Assembly.

Note IIP, IIP+, IIIP: Short C212 on the DC Controller to bypass error 50 time delay. (The printer must be turned off.)
IIISi/4Si Only:
1. Make sure fuser is correctly seated to AC Power PCA.
2. Reseat connector J201 on Sensor PCA.
3. Check SW101 to make sure it is engaged with top cover closed.

Note IIISi/4Si: Short cp005 on DC Controller to bypass Error 50 time delay. (The printer must be turned off.)

5Si/4000/4050/4100/5000/8000/8100 Only:
The fuser is malfunctioning.
50.1 Fuser low temperature failure.
50.2 Warm-up failure(timed out).
50.3 Over temperature failure.
50.4 Bad fuser.
50.5 Inconsistent Fuser Temp.

51 ERROR (Loss of Beam Detect)
2686 Only:
1. Bad laser unit or improper laser power setting.
2. Replace Laser Diode Assembly.
3. Replace Scanner Assembly.
II, III Only:
1. Replace Cable, Laser/Scanner to DC Controller cable. (P/N RG1-0908-000)
II, IID, III, IIID Only:
1. Inspect the Fiber Optics Cable for cuts or kinks.
2. Replace Laser/Scanner Assembly.
3. Replace DC Controller.
IIISi/4Si Only:
1. Visually check or replace toner cartridge.
2. Inspect Fiber-Optic Cable between Laser/Scanning Assembly and DC Controller.
3. Reseat connectors J002 on the DC Controller and J601 on the LaserDrive PCA.
4. Replace Laser/Scanning assembly.





最新文章
推荐文章
网友热门关注
· HP LaserJet Error Codes
· Canon Waste Tank Reset Codes (Several Printers)
· EPSON COLOR 777 General Error Red light on
· canon BJC-85 Printer Error Codes
· canon ink tank full error message S9000 S900
· Lexmark Optra S1255 -900 Service RIP Software
· Epson Stylus Color 400 Adjustment Program Needed
· Horizontal Stripes on printout of HP LaserJet IIIp
· HP 4050 Paper Jam but there is none
· HP laserjet 1505n Printer Problem Not Taking paper
· HP LaserJet 2100 Pickup Roller
· HP Deskjet 845c Resume light flashing
· HP LaserJet 4050 Intermittent Error 13.1, Sensor?
· Epson 1520 won't recognize new ink cart
· HP Deskjet 970cxi cartridge status light
· HP CLJ 3800 - Error Code 51.23
· Epson C82 Vertical Banding - Magenta only
· HP Laserjet 2300 Firmware problems
· hp office jet 600 cartridge error message
· Epson R800 Won't Feed Paper
· hp psc 750 - remove and check black cartridge
· Brother MFC9600 Error 72
· HP PSC 2410 Carriage blocked error.
· hp 4550 ,49.XX PRINTER ERROR
· Brother 5100c Print Head Problem
· Epson 870 cyan/magenta banding problem
· HP LJ 3100 - Printer Paper Jam Check Paper Path
· HP 1220c will not initialize
· HP color laserjet cp 6015/6040MFP Cold Reset/Hard Disk Init
· Canon iP4500 Sheet Feeder Error
· Canon S520 "not responding"
· HP 6P fuser, error codes, and memory
· hp 5000 fuser error
· Canon S750 Black ink streaking
· Canon i320 Printhead not installed msg - error!
· EPSON LQ-300k 针式打印机故障维修2例
· HP LaserJet 4000n - 13.1 Paper Jam
· HP LaserJet 4300dtn error 13.01.00 and 13.06.00
· HP4100. error code 49.4C02
· HP laserjet 4000n, message error 52.0 printer error followed by cycle power continue.
· HP4500DN Print Vertical Lines/Right Side
· HP Laserjet 4000 print out only one line per page
· Canon BJC-6200 6 orange blinks, 1 green solved!
· Canon BJC 6200 waste reset
· HP LaserJet 4000N Paper Jam from Tray 1
· Samsung ML-1450: Errors
· PCL5, PCL6, PostScript - which one to choose?
· Canon i6500, major problems !
· HP 2000C: No cartridge expiration date!?
· Epson stylus 880 - all lights blinking!
· Error C0204 for Konica Minolta Bizhub 250
· HP LaserJet 5000dn error "50.2 fuser error"
· Hp 4050 print image problem
· HP LaserJet 6P light and uneven print
· Epson Stylus C80 Print Black Ink Only Please
· Canon i850 Prints but no ink comes out
· epson 670 3 lights flashing
· Lexmark Error 935 Print Head Error
· Minolta 3050 error code Description
· EPSON 1290 (1280) PRINTHEAD CABLE REMOVAL
· canon mpc 190 error message: wrong cartridge
· HP Laserjet 1200 Intermittent Problem
· HP 610CL Blinking Orange Light on
· Lexmark 4049-12R - Error 935, 933, 932
· Xerox Phaser 8400 error 07.010.43
· HP Laser jet 8150N Display message 79.00FE
· Epson EPL-N2750 Service Req C0082
· HP 930c cartridge jam, grind
· Canon i9950 Installation Problem on Mac OS X
· HP LaserJet 1100 light flashes amber
· HP Color Laserjet 4500, 49 Error (04FF) Cycle Power
· HP 4550 laser printer 13.1 false jam
· Epson 1270 Communication error
· canon bjc 240 problem light blink green
· hp 2300d - 13.20.00 message
· HP 5P no paper pickup
· HP Color Laserjet 4500 paper feed issues
· Epson C80 "Service Required"
· HP deskjet 3820 won't turn on
· HP Deskjet 6122 black-toner printing problems
· Minolta 2150, 2151, 2152 error code Description
· HP Laserjet 1100 printing blank sheets
· hp deskjet 612c blinking resum
· HP 4550 Error code 54.2 after replacing toner cartridge
· Canon S820 print head error - waste ink tank?
· HP 1100 out of paper error
· HP LASER JET 8150, the message "50.1 fuser error".
· hp1280 red light on green light off
· HP LJ 5000 57.1 error
· HP LaserJet 6P Error tray light flashes orange about twice every second.
· Canon LBP-2900 , replacing first dud. Black ink tank empty, installed new tank.
· HP 2000c all the lights start flashing in error state.
· HP DesignJet 750C Plus paper jam problem
· Canon Laser Class 7500 'Supply Rec Paper' error
· HP 8150 57.5 error
· Epson 1290 print failure & inconsistent resolution
· hp psc 2175 carriage jam
· Epson 1520 EEPROM reset from control
· HP deskjet 5550 that doesn't sense paper